Owners manual
Page 2 of 7 292-2759 Rev. G 2/11/11
Page 3 of 7 292-2759 Rev. G 2/11/11
2005-12 Nissan Xterra
Installation Instructions
BX1836
Parts List
Ref.No. Qty. Part # Description
1 1 61-6161 Weldment, Baseplate, BX1836
2 2 61-3799 Weldment, 1/2”-13 Nut Plate, w/ 10” Wire
3 2 201-0051 1/2”-13 x 1 1/2” Hex Bolt, Grd. 5, ZP
4 2 203-0012 1/2” Lock Washer, ZP
5 4 201-0603 12MM-1.25 x 45MM Hex Bolt, Grd. 8.8, ZP
6 4 203-0105 12MM Lock Washer, ZP
7 4 203-0005 1/2” Flat Washer, ZP
8 2 201-0053 1/4”-20 x 1/2” Hx. Wshd, Type F Screw
9 2 201-0192 #10-32 x 1/2” Slot, Rd. Hd. Screw
10 2 203-0054 #10 Lock Washer
11 2 202-0047 #10-32 Hex Nut
12 2 101-5822 Adapter, 4 Way Connector
13 2 62-3468 Attachment, Assembly, SF/SB (R)
2 226-0049 Baseplate Safety Cable, 36” CL IV (NS)
4 229-0512 Quicklink, 1/2, ZP (Not Shown)
2 290-0437 Cap Plug, Black (Not Shown)
Important:
Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need
of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade. In most cases it
will be Grade 5-please reference the parts list above. Replacement parts may be ordered through your nearest Blue Ox® dealer or distributor,
or call our Customer Care Team at (402)385-3051. Failing to follow and/or altering these installation instructions in either installation or
required equipment will void the manufacturer’s warranty.
Tools Required
10MM Socket
17MM Socket
Phillips Screw Driver
19MM Socket
Loctite Red
Reciprocating Saw
34” Socket
1 1/4” Hole Saw
Attachment Tabs:
Due to the design of the removable tabs, the
RangeFinderII tow bar can not be used. Adapters,
except the BX8833 and BX88151, can not be
used with this baseplate.
Instructions:
The front fascia, fascia brace and metal
bumper are removed for the baseplate
installation. Drilling is required.
Some vehicles bellypan may need trimming.
The dimensional variations between otherwise
identical vehicles can be considerable.
Although the baseplate was designed for easy
installation, it may be necessary to tailor the
baseplate slightly to compensate for auto
manufacturer’s tolerances. These minor
adjustments may include ling a hole slightly,
bending electrical rods or bending end plates.
The Bx8869 Bulb and Socket Wiring Kit is
recommended for this vehicle.
2005-12 Nissan Xterra
Installation Instructions
BX1836
2. Pull the fascia forward in order to release the clip
on the back. Pull up and release four clips along
the bottom of the front fascia. Set the fascia aside
carefully. Do this on both sides of the fascia. The
driver’s side is shown in the picture above.
2
1. Remove the three pushpins on the front fascia near
the headlight housing. Set aside to be reinstalled
later. Do this on both sides. The passenger’s side
is shown in the picture above.
1
Possible location for the BX8869 Bulb &
Socket Wiring Kit.
Installation Instructions:
Handling of some cosmetic parts
when installing this product may
require the use of protective covers,
rags, specialty tools, etc. to prevent
damage.