Replacement Part List

ManualsBrandsBlue Max ManualsChainsaw Parts & Accessories4,200 RPM Bench Mount Electric Chainsaw Sharpener

8805655 07/15

CHAINSAW SHARPENER

For Customer Service, please call 1-800-348-5004 or

email feedback@natitools.com

Model: 5655

CALIFORNIA PROPOSITION 65

WARNING: You can create dust

when you cut, sand, drill or

grind materials such as wood,

paint, metal, concrete, cement,

or other masonry. This dust

often contains chemicals known

to cause cancer, birth defects,

or other reproductive harm.

Wear protective gear.

WARNING: This product or its

power cord may contain

chemicals, including lead,

known to the State of California

to cause cancer and birth

defects or other reproductive

harm. Wash hands after

handling.

IMPORTANT!

When using equipment, a few

safety precautions must be

observed to avoid injuries and

damage. Please read the complete

operating manual with due care.

Keep this manual in a safe place,

so that the information is available

at all times. If you give the

equipment to any other person,

give them these operating

instructions as well. We accept no

liability for damage or accidents

which arise due to non-observance

of these instructions and the safety

information herein.

CAUTION:

FOR YOUR OWN SAFETY

READ INSTRUCTION

MANUAL COMPLETELY

AND CAREFULLY BEFORE

OPERATING THIS BRUSH

CHAINSAW SHARPENER.

SPECIFICATIONS

Electrical Rating:

120VAC / 60Hz / 0.7A

Motor No Load Speed:

4,200 RPM

Arbor Size: 7/8"

Max. Accessory Diameter:

4-1/4″ (108mm)

Max. Wheel Thickness:

1/8"

Mounting Hardware:

2x1/4″ Bolts and Nuts

(Not included)

SAFETY WARNINGS

1. KEEP GUARDS IN PLACE

and in working order.

2. REMOVE ADJUSTING KEYS

AND WRENCHES. Form habit

of checking to see that keys and

adjusting wrenches are removed

from tool before turning it on.

3. KEEP WORK AREA CLEAN.

Cluttered areas and benches

invite accidents.

4. DON’T USE IN DANGEROUS

ENVIRONMENT. Don’t use power

tools in damp or wet locations, or

expose them to rain. Keep work

area well lighted.

5. KEEP CHILDREN AWAY.

All visitors should be kept safe

distance from work area.

6. MAKE WORKSHOP KID PROOF

with padlocks, master switches,

or by removing starter keys.

7. DON’T FORCE TOOL.

It will do the job better and safer at

the rate for which it was designed.

8. USE RIGHT TOOL.

Don’t force tool or attachment

to do a job for which it was not

designed.

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this

product. Observe all safety information to protect yourself and others. Failure to observe the instructions may

result in property damage and/or personal injury. Please keep instructions for future reference.

Important Operating Instructions

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

4004713

Summary of content (10 pages)

PAGE 1
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property damage and/or personal injury. Please keep instructions for future reference.
PAGE 2
Table A: RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25′ 50′ 100′ 150′ 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
PAGE 3
4. Always use guards and eye shields. 5. Do not overtighten wheel nut. 6. Use only flanges furnished with the grinder. 7. Adjust distance between wheel and work rest to maintain 0.125” or less separation as the diameter of the wheel decreases with use. 8. Frequently clean grinding dust from beneath grinder. 9. Wear a full face shield over ANSI-approved safety goggles during use. 10. Do not grind with side of wheel unless wheel is specifically designed for that type of grinding. 11.
PAGE 4
5. Grip workpiece as lightly as possible (while still keeping safe control of it). Let the tool do the work. 6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SETUP - BEFORE USE: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
PAGE 5
OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TOOL SET UP TO PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED. INSTALLING THE GRINDING WHEEL 1. The Grinding Wheel MUST be: • Rated to at least 5,000 RPM. • No larger than 4-1/4″ in diameter. • Fitted with a 7/8″ round arbor hole. • 1/8″ thick or less. • Dry and clean.
PAGE 6
c. Pull down on the Handle to bring the Grinding Wheel into the Gullet, then make adjustments: • Turn the Chain Stop Adjustment Knob until the Grinding Wheel just grazes the cutting edge. Tighten the Chain Stop Lock Nut. • Turn the Depth Adjustment Knob until the Grinding Wheel is just above the bottom of the Gullet. Tighten the Depth Adjustment Lock Nut. Cutting Edge Gullet Figure F: Right-hand Cutter d. Plug in the Sharpener and turn it on. e. Allow the Sharpener to come up to full speed. f.
PAGE 7
TROUBLESHOOTING Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 2. No power at outlet. Tool operates slowly. Performance decreases over time. 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Turn off tool and allow to cool. Press reset button on tool. 4. Have technician service tool. 3.
PAGE 8
Limited Manufacturer Warranty and durability standards. NATI warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, or accidents, repairs or alterations, or a lack of maintenance.
PAGE 9
CHAINSAW SHARPENER Model: 5655 Parts List 6 7 8 9 10 11 12 13 14 15 16 17 18 19 4 3 20 2 21 1 22 35 23 24 36 25 61 37 60 38 39 40 59 30 41 31 42 32 43 58 44 33 57 45 34 56 46 55 47 48 49 50 51 52 53 54 For Customer Service, please call 1-800-348-5004 or email feedback@natitools.
PAGE 10
Parts List Call 1-800-348-5004 for assistance or replacement parts Address any correspondence to: Please provide the following information -Model number North American Tool Industries 84 Commercial Rd Huntington, IN 46750 -Part description and number as shown in parts list -Serial number Part 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30 31 32 33 34 Description Screw Back Cover Screw Pressure Panel Circuit Panel Motor Vise Handle Handle Lower Valve Power Switch Cushion Depth Adjus