Installation & Operation Instructions

Five-Year Limited Warranty.
Complete Warranty Terms Located at: sensorworx.com/warranty
INS40x-B | REV 001–200611
SENSORWORX | 2a Research Parkeway, Wallingford CT 06492
203.678.4224 | www.sensorworx.com
© 2020 BLP Technologies, Inc. All rights reserved.
TESTING & TROUBLESHOOTING
COVERAGE TEST MODE
To put a sensor in COVERAGE test mode for 10 minutes:
1. Press and release the button two times.
2. Once the LED blinks white, press and release the button one additional time.
3. The LED will blink back white three times and then rapid ash twice indicating the change to test mode was sucessful.
To test coverage, wait until lights turn off then walk into range of sensor. While in test mode the LED will blink when it transmits an occupied signal (maximum of once every 4 seconds).
After 10 minutes, the unit will automatically exit test mode.
Note: Once test mode has been inititated from a linked sensor, the linked controller will ignore all other sensors until a new sensor initiates test mode or the 10 minutes expires.
TESTING WIRELESS LINKING (PAIRING)
1. Press and release the button one time.
Lighting controlled by any/all linked load controller(s) will toggle one time as conrmation.
SETTING # DESCRIPTION
3 Restore Factory Defaults
4 Send a “Forget Me” Message to all Paired Controllers
RESTORING FACTORY DEFAULTS / UNPAIRING
To return a wireless sensor to its original factory default settings or to unpair from all linked wireless load controllers the following commands can be executed.
ENTERING A RESTORE FACTORY DEFAULTS OR FORGET ME COMMAND
1Read through the above list and note the number of the desired command
2 Press and release the unit’s pushbutton 8 times, then wait 2 seconds.The White LED will blink back 2 times, pause and repeat.
3 Interrupt the blink back and press the pushbutton the number times equal to the desired command (e.g. 3 times to Restore Factory Defaults).
4 The LED will ash back the command number as conrmation and will be executed after three conrmations. Two sets of rapid White ashes indicates success. If the Blue LED rapid
ashes twice, the command was unsuccessful and process should be started over.
FCC INFORMATION (FCC ID: 2AVRY-SWX0002)
ISED CANDADA INFORMATION (IC: 26012-SWX0002)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
1. This device many not cause harmful interference, and
2. This device must accept any interference received, Including interference that may cause undesired operation
Changes and Modications not expressly approved by BLP Technologies can void your authority to operate this equipment under Federal Communications Commission’s rules.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
3. An de se conformer aux exigences d’exposition RF FCC / ISED, cet appareil doit être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help