002 WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS MAINTENANCE INSTRUCTIONS EXPLODED VIEW & PARTS LIST WIRING DIAGRAM PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 5 6 8 9 10 INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance.
FEATURES & OPERATING CONTROLS A. INFINITE SWITCH 1. On INFINITE SWITCH CONTROLLED warmers, power is applied to the heating element based on the control knob position and the amount of energy consumed. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob may have a numeric scale, where higher numbers correspond to higher temperature. LO is the lowest temperature setting; PREHEAT is a “continuous on” setting.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. WARNING: RISK OF INJURY Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage.
OPERATION WET OR DRY OPERATION CAUTION: 1. Carefully read the description of the warmer operation on the specification sheet. 2. If the warmer is to be used for WET operation, add approximately 1” of hot tap water before turning the warmer ON. Use of hot water will allow a faster preheat. a. Check the water level frequently and add hot water as necessary to prevent the warmer from running dry. Do not add water to the warmer if it has run dry. b.
CLEANING INSTRUCTIONS CAUTION: SHOCK HAZARD Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Unplug the warmer. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily.
CLEANING INSTRUCTIONS (continued) WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Circuit breaker off or tripped Reset circuit breaker Unit not plugged in Make sure unit is plugged in to power receptacle Temperature control not set Set control to desired temperature Internal damage Contact you Authorized Wells Service Agency for repairs Wet insulation Allow to dry or replace insulation Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact you
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
EXPLODED VIEW & PARTS LIST MODEL SW-10 TOP AND POT ASSEMBLY D8-40427 TRADEMARK DOMED LABEL 2M-300534 TRIM RING ASSEMBLY D8-30256 WE LL S PROTECTOR DD-35890 HEATING ELEMENT WS-506274 INFINITE SWITCH 2E-30570 ELEMENT COVER 2D-31878 CONTROL KNOB ASSEMBLY 2R-40498 120V CORDSET (4FT) DD-22231 SAFETY THERMOSTAT WS-50374 THERMOSTAT BRACKET DD-31683 1” ADJUSTABLE LEG 2A-41946 STRAIN RELIEF 2K-31217 IL2419 Model: SW10 10 002 p/n 2M-303306 Owners Manual Countertop Warmer Infinite Switch Control AMBER LI
002 p/n 2M-303306 Owners Manual Countertop Warmer Infinite Switch Control WIRING DIAGRAM 11
PARTS & SERVICE Always use an inset. DO NOT place food directly into the warmer pan. DESCRIPTION PART NO. ADAPTERS & INSETS ADAPTER TOP, convert SW-10 from 11 qt. to 4 qt. Inset WS-20822 ADAPTER TOP, convert SW-10 from 11 qt. to 7 qt. inset WS-20175 4 QT. ROUND INSET w/ lid WS-20774 7 QT. ROUND INSET w/ lid WS-20587 11 QT. ROUND INSET w/ lid WS-20908 11 QT.
PARTS & SERVICE (continued) DESCRIPTION PART NO. LEGS, 1” Plastic, set of 4 WS-21109 LEGS, 2” Plastic, set of 4 WS-20605 *LEGS, 4” Plastic Adjustable, set of 4 WS-20314 IMPORTANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: *LEGS, 4” Metal, Adjustable, set of 4 WS-20563 Wells Bloomfield, LLC ACCESSORIES * Not for use on all appliances.
WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.
