OWNER'S MANUAL OPERATING INSTRUCTIONS MAINTENANCE INSTRUCTIONS and INTEGRITY™ Brewing Systems FOR PARTS LIST ICED TEA 70473 8746-M BLOOMFIELD INDUSTRIES 2 ERIK CIRCLE, P.O.
INDEX INTRODUCTION TO THE UNITS ............................................……………. ...3 UNIT SET UP ..................................................................................………..…3& 4 BREWING OF TEA..................... ..................... .........................……………....4 TEABREWERADJUSTMENTS……………………………………………………4 TIMER/VOLUME ADJUSTMENT BREWER WATER VOLUME ADJUSTMENT……………………………………5 RATIO CHANGE PARTS LIST .................................... ............................................……………..
INTRODUCTION TO THE UNITS This manual covers the six (6) gallon tea brewer and the six (6) gallon tea dispenser. 1. The Model 8746 is the tea brewing section only and does not have a storage and/or dispensing reservoir as part of the unit. 2. The Model 8806 is the six (6) gallon stainless steel reservoir to hold the finish brew. All brewers are shipped from the factory with: 1. 2. 3. 4. A Stainless Steel Brew Funnel.
9. After end of final cycle, turn tank heater switch to ON position - top portion of switch rocker pressed in. 10. When tank water is up to proper temperature, the green READY TO BREW light will be lit. 12. NOTE: During the initial heatup, some water will drip from spray disc. This is normal. Discard water in six gallon dispenser, place brew-through cover on dispenser then reposition empty dispenser on brewer. 13. Place filter and tea in brew chamber. Slide brew chamber into place on brewer. 14.
BREW WATER VOLUME ADJUSTMENT (Ratio Change) 1. 4. Water flow from spray disc and dilute spout should be measured separately to determine that the desired ratio has been achieved. Follow steps 1 through 4 in Timer Adjustment Procedure. 2. Turn the handle of the needle valve clockwise IN (facing the valve stem and handle) to increase the ratio. This causes more water to be diverted to the dilute flow, and less to the brew. A counter-clockwise OUT rotation will do the opposite.
REPLACEMENT PARTS LIST - OF BREWING UNIT MODEL 8746 REF. NO. 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 1 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 44 45 46 47 49 50 PART NO. DESCRIPTION 8543-52 8746-12 7200-6X 8043-5 8043-47 8543-69 #08x3x8 B.PN.P.SS BASIN TOP WELDED #O8-32 X 5/16 PN.P.SS HOLD DOWN STRAP ASSY #10-32 X 1 PN.P.
REPLACEMENT PARTS LIST REF. NO. 51 52 53 54 55 57 59 60 61 62 63 65 66 67 68 69 70 71 72 73 74 75 76 77 (continued) PART NO. DESCRIPTION 8043-30 8710-10 8043-12 8043-28 8512-41 8512-51 88 12-34 8043-83 8746-28 8746-21 8942-92 8746-30 D 20002-3 8033-56 8033-55 88 12-47 8746-27 8746-29 35-210 8942-48 8812-73 8812-80 7506-39 3-100 HTG ELEMENT GASKET NUT 7/16-20 X 1/8 TANK COVER GASKET NUT, HEX /2-20 2B SEAL WASHER THERMOSTAT - R. SHAW TANK COVER.
EXPLODED VIEW - OF BREWING UNIT /-- MODEL 8748
EXPLODED VIEW FOR RESERVOIR AND DISPENSER SECTIONS OF MODEL NO. 8808 ‘1’ 9 d IO 1 2 85 MODEL NO. 8806 Model Without Slght Glass REPLACEMENT PARTS LIST PART NO. DESCRIPTION 1 6600-50 Nut 2 8600-28 Flat Washer 3 6600-12 Nylon Washer 4 6600-6 Siynk 5 6600-15 Faucet ONLY, Plastic 6 6700-25 L Seat Cup 7 6600-26 “c” Ring 6 6600-27 Wing Nut 9 6942-33 Gasket 10 6606-l VS%l 11 6606-5 ClY4er 12 66061 Label (“Luzianne” _ not shown) REF NO.
ADDITIONAL SERVICE INFORMATION COLD WATER ENTRANCE SOLENOID VALVE PART NO. 8541-120 ,ton*irtr Of hl”F and Flow Control, SOLENOID VALVE REPLACEMENT PARTS (For Black Coil Valve) INo Kit Parts Sold Separately) (1) 8541.120CS Coil Assembly 120V.
WARRANTY BREWER WARRANTY IS VOID IF: For a period of one (1) year from date of installation, all defective parts on Bloomfield equipment will be replaced free of charge, providing parts did not become defective through accident, neglect, improper installation, mishandling or damage in transit. The service necessary to replace these defective parts will also be free of charge, provided this service is performed by an authorized BLOOMFIELD service station, wherever authorized service is available.
INSTALLATION INSTRUCTION FOR BASE EXTENDER KIT #83334 FOR MODEL 8748 TEA BREWER h 1 / 2 FIGURE A ELECTRICAL SHOCK HAZARD: Turn off the Tank Heater Switch and disconnect - * power supply to Brewer before removal of any panel. Electrical shock will cause death or serious Injury. Wait until the water in the tank has cooled down to room temperature before Installing this Kit. Failure to comply will cause severe burns. CAUTION: STEP 1: Remove the Screws from the Back Panel (ITEM 1). Remove the Back Panel.
