Dishwasher Installation Manual FOR MODELS DWT 23100 B DWT 23100 SS DWT 23100 W DWT 24100 B DWT 24100 SS DWT 24100 W DWT 24400 SS ULTRA DWT 24400 W ULTRA DWT 25100 B DWT 25100 SS DWT 25100 W DWT 25200 BWS DWT 25200 SSWS DWT 25200 WWS DWT 25300 B DWT 25300 W DWT 25300 SS DWT 25500 B DWT 25500 W DWT 25500 SS DWT 54100 B DWT 54100 FBI DWT 54100 SS DWT 54100 W DWT 54400 SS ULTRA DWT 54400 W ULTRA DWT 55100 B DWT 55100 FBI DWT 55100 SS DWT 55100 W DWT 55200 BWS DWT 55200 FBIWS DWT 55200 SSWS USA DWT 55200 WW
Installation Manual For Dishwasher Models Cycle Select Start / Pause Half Load / Tablet Time Delay DWT 23100 B DWT 23100 SS DWT 23100 W DWT 24100 B DWT 24100 SS DWT 24100 W DWT 24400 SS ULTRA DWT 24400 W ULTRA DWT 25100 B DWT 25100 SS DWT 25100 W DWT 25200 BWS DWT 25200 SSWS DWT 25200 WWS DWT 25300 B DWT 25300 W DWT 25300 SS DWT 25500 B DWT 25500 W DWT 25500 SS DWT 54100 B DWT 54100 FBI DWT 54100 SS DWT 54100 W DWT 54400 SS ULTRA DWT 54400 W ULTRA DWT 55100 B DWT 55100 FBI DWT 55100 SS DWT 55100 W
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. Contents 1. IMPORTANT SAFETY INSTRUCTIONS 1 1.1 INSPECT THE DISHWASHER 1.2 HOW TO CONTACT US 2 2 2. TOOLS WHICH MAY BE NEEDED 3 3. MATERIALS WHICH MAY BE NEEDED 3 4. MATERIALS SUPPLIED 4 4.1 PARTS SUPPLIED 4.2 MANUAL BAG 4.3 DISHWASHER PARTS BAG 1 4.4 DISHWASHER PARTS BAG 2 4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4 4 4 4 4 5.
INTRODUCTION Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. Be sure to observe all listed warnings and cautions. Look particularly for the icons with exclamation marks inside. The information icon also will provide important references.
Replacement - If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary. Dishwasher must be secured to adjacent cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury. Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. UL listed conduit connector or strain relief. Teflon tape or other pipe thread compound to seal plumbing connections.
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED a. x1 b. x1 Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. c. x1 4.2 MANUAL BAG d. x6 e. x1 The dishwasher comes with a manual bag containing: User manual, Installation manual and Quick reference guide. f. x1 4.3 DISHWASHER PARTS BAG 1 g. x1 h. x1 j. x1 k. x1 l. x1 m. x1 n. x2 o. x1 p.
34 - 361/4 (864mm - 920mm) 5. DISHWASHER SPECIFICATIONS 24m) 0m (61 33 7/8- 35 7/8 (861mm - 911mm) 239 (598 /16 mm ) 2 (61 4 0m m) max 500mm axax) mm 24 m 0m 61 ( 5.1 TECHNICAL FEATURES Load capacity 12 place settings Permissible water pressure 4.35 - 145 psi (0.
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury.
Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. Notice : Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. Turning the screwdriver in the direction of the black arrows will bring the dishwasher back feet up.
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. Check with your plumbing supply sources for the proper hose and 90° elbow and necessary fittings for the water supply line. This material is not supplied, and must be purchased separately.
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice : Either one of the above methods must be used or the dishwasher will not operate properly. A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged. The total length of the drain hose is 763/4” (1950mm).
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a damp cloth (as shown in Figure A). Once the area dries, apply the steam protection foil.
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 7.1.1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing. 1.
7.1.2 PREPERATION OF WATER SUPPLY Left side water supply connection A Before pushing the dishwasher in to the cabinet you must place water supply hoses into the channel of the dishwasher (Figure A). Place the supplied clips into the channel (Figure B) so that you can move these clips along the channel (Figure C) and fix by pressing on (Figure D) so that you can keep the water supply hose in the channel.
After installing one clip for each side push the dishwasher into the cabinet (Figure E). E Note that while pushing the dishwasher into the cabinet, water supply hose must move in the channel to the front (Figure F). F Fix the second clip (Figure G).
7.1.3 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: With metal braided hose. With copper tubing. CAUTION Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Temperatures required for soldering and sweating will damage the dishwasher’s water inlet valve so if any such operation is needed, keep the heat source min. 77/8” (200mm) away from the dishwasher’s water inlet valve.
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. Ø 1/8" (3,5mm) Ø 1/8" (3,5mm) 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. 2. Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied.
o A B t s C If the enclosure height is above 331/16” (840mm) use “o” and “p” labelled toe kicks together. Make sure the slotted toe kick “p” is on the outside so you can adjust height of the toe kick. Installation should be done following the steps illustrated in the figures A, B and C respectively. 1. Align the toe kick (o) and (p) (A). 2. Secure toe kicks to brackets with screws (t) after adjusting the height of the slotted toe kick (p) (B). 3. Attach caps (s) as shown in the supply bags (C).
2. To take the plastic bracket out, remove the screws on it. Screws will be used in 5th step again. (Figure B). B 3. Mark the wooden door as shown in the drawing (Figure C). D 4. Place the plastic mounting brackets over the marked holes and the side tabs must be flush with the edge of the wooden door (Figure D).
Ø 1/8" (3,5mm) 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A). x4 v A 6. Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached (Figure B). B 7. Open the door and remove the two caps and two screws inside the door at position 1 and 4 (Figure C).
8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 4 (Figure A). Ø 3/16" (4mm) x4 y A 9. Check the position of the wooden door and make sure it is aligned properly (Figure B). B 10. Tighten the screws in position 1 and 4 completely after the final alignment (Figure C).
B 11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). 11.1. If the door hits the toe kick cut the necessary section out of the toe kick (B). 11.2. Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
Notice : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
8. INSTALLER CHECKLIST 10. SELF HELP HINTS: Your installer must have completed and checked the following: The dishwasher is square and level. The dishwasher is fastened securely to the cabinetry. The dishwasher door opens and closes freely. The dishwasher door must close without hitting any cabinetry or counter top. The inlet water supply is turned on and checked for leaks. The drain hose has been connected and checked for leaks. There must be no kinks or obstructions in the drain hose.
17 9077 01 00-AC-USA
