Programming instructions

OPERATION & CALIBRATION
1-9
PROGRAMMING MULTIPLE STAGE RECIPES
Entering the Programming Mode:
1. Press and hold the PROG KEY (10). The top disĆ
play reads CodE.
2. Use the product keys to enter the programming
access code: 3 1 2 4. Press the ENTER KEY (14).
The top display reads Prod.
3. Press the desired product key followed by the
ENTER KEY (14).
Programming the Cook Time:
NOTE: When multiple stage cooking is being used,
the countdown time displayed during cookĆ
ing is the sum of all stages.
1. The top display reads P1:__. The bottom display
gives the current programmed cook time for
stage 1 in minutes:seconds. Press the TOGGLE/
CLEAR KEY (11). Use the product keys to enter
the new cook time. Press the ENTER KEY (14) to
save the new cook time.
2. The top display reads P2:__. The control is askĆ
ing for the cook time for the second stage of this
recipe. Repeat Step 1 for each additional stage.
3. When the cook times for all stages are proĆ
grammed, press the TOGGLE/CLEAR KEY (11)
to clear the bottom display.
NOTE: This tells the controller that there are no
more stages for this recipe. Once the
number of stages has been established
the control will only allow entries for
these stages on all further parameters for
this product.
4. Press the ENTER KEY (14) again. The display
reads P1:. The bottom display shows the cook
time.
5. Press the SCAN KEY (15) to advance the proĆ
gramming mode to cook temperature.
Programming the Cook Temperature:
1. The top display reads Ct-1. The bottom display
gives the current cook temperature for stage 1 of
this recipe. Use the product keys to enter the deĆ
sired cook temperature.
2. Press the ENTER KEY (14) to save the new cook
temperature for stage 1. The top display reads
Ct-2.
NOTE: Repeat Steps 1-2 to program the cook
temperature for additional stages. When
the cook temperature for the final stage
has been entered the top display reads
Ct-1.
3. Press the SCAN KEY (15) to advance the proĆ
gramming mode to fan speed
Programming the Fan Speed:
1. The top display reads SPd1. The bottom display
gives the current fan speed. Press the TOGGLE/
CLEAR KEY (11). The bottom display toggles beĆ
tween HI and Lo.
2. Press the SCAN KEY (15) to advance the proĆ
gramming mode to the fan cycle time.
Programming the Fan Cycle Time:
There are 3 options for fan cycle time: Pulse, Heat
and Full. Pulse allows the fan to turn on and off as
programmed. Heat allows the fan to operate with
heat only. Full provides continuous fan operation.
1. The top display reads CYC1. The bottom display
gives the current fan cycle for stage 1. Press the
TOGGLE/CLEAR KEY (11). The bottom display
toggles between PULS, HEAt and FULL.
2. Press the ENTER KEY (14) to save the new fan
cycle for stage 1. The top display reads CYC2.
NOTE: Repeat Steps 1-2 to program the fan
cycle for additional stages.
3. When the fan cycle for the final stage has been
entered press the SCAN KEY (15).
If no pulse cycles are programmed the control
advances to timing mode.
If pulse is used, the control returns to the first
stage programmed for the pulse fan option. FolĆ
low Steps 4-5 to program the pulse on and off
time.
4. The top display reads on-x. The bottom display
gives the current pulse on time for this stage. Use
the product keys to enter the desired pulse on
time from 10 to 60 seconds. Press the SCAN KEY
(15).
5. The top display reads of-x. The bottom display
gives the current pulse off time. Use the product
keys to enter the desired pulse off time from 10
to 60 seconds. Press the SCAN KEY (15). The