Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS LB-Par™ RGBW 1 1. Getting Started 3 What’s In The Box? Getting It Out Of The Box Powering Up! Getting A Hold Of Us Safety Instructions (Don’t Stick Your Hand In The Toaster!) 2. Meet The LB-Par™ RGBW 3 3 3 3 4 3 Features DMX Quick Reference The LB-Par™ RGBW Pin-up Picture 5 5 6 3.
1. GETTING STARTED What’s In The Box? • 1 x LB-Par™ RGBW Professional LED Fixture • An Ever-So-Handy Power Cord • This Lovely User Manual Getting It Out Of The Box Congratulations on your purchase of one super-cool 4-in-1 LED PAR can! Now that you’ve got your LB-Par™ RGBW (or hopefully, more!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2.
Figure 1: The LB-Par™ RGBW Pin-Up Picture Heavy-Duty Composite Housing High Output 4-in-1 Quad Color LEDs Secure Grip Locking Knobs Dual Mounting Brackets Figure 2: The Rear Connections Mic Sensitivity Menu Display Menu Buttons Microphone Power Out Power In DMX In DMX Out Page 6 LB-Par™ RGBW User Manual Rev.
3. SETUP Fuse Replacement CAUTION! The LB-Par™ RGBW utilizes a high-output switch-mode power supply with an internal fuse. Under normal operating conditions, the fuse should not require replacement. The fuse is field replaceable, however it is an advanced procedure suited to qualified individuals. Should your LB-Par™ RGBW fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!) CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
USING THIS FIXTURE WITH THE wiCICLE® WIRELESS DMX SYSTEM In addition to the unbridled thrill you already received the first time you plugged in your fixture, you’ll be delighted to know that This fixture also works seamlessly with our wiCICLE® Wireless DMX system, without additional power. • ONLY fixtures bearing this logo are certified for use with the wiCICLE® without external power. • Unauthorized modification and/or using the wiCICLE® with unapproved fixtures may cause damage to the wiCICLE® or fixture.
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the LB-Par™ RGBW are accessed by using the control panel on the rear of the fixture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.
Control Panel Menu Structure Addr 1-512 To choose the DMX address CHNL CH-1 4-channel DMX mode CH-2 9-channel DMX mode SP-- 0-99 Speed adjustments (0-99) Pr-- 1-13 Built-in programs (1-13) SOUN Sound active mode CoLo 1-15 Built-in colors (15 = off) Strb 0-20 Flash / strobe speed rL-- 000 - 255 Red intensity (0% <--> 100%) GL-- 000 - 255 Green intensity (0% <--> 100%) bL-- 000 - 255 Blue intensity (0% <--> 100%) uL-- 000 - 255 White intensity (0% <--> 100%) LEd on-
DMX Mode Allows the unit to be controlled by any universal DMX controller. Set the Starting DMX Address: The default mode for the fixture is DMX, so the first menu item that you can edit is the starting DMX address. 1.) Navigate the main menu until you reach Addr, and press . 2.) Use the buttons to select a DMX channel from 001-512. 3.) Press the button to confirm. Select the DMX Channel Mode: 1.) Navigate the main menu until you reach CHNL, and press . 2.
LED Display On/Off: You can set the LED menu display to either stay on continually, or turn off after 30 seconds of inactivity. 1.) 2.) 3.) 4.) Navigate the main menu until you reach LEd, and press . Use the buttons to highlight either on or oFF. The On setting will keep the display on continually, and oFF will turn the display off after 30s. Press the button to confirm your choice. Dimming Speed & Curve Settings: You can manually set the fixtures dimming curve of your choice: 1.
5. APPENDIX A Quick Lesson On DMX DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre Technology (USITT) as a standardized method for connecting lighting consoles to lighting dimmer modules. It was revised in 1990 and again in 2000 to allow more flexibility. The Entertainment Services and Technology Association (ESTA) has since assumed control over the DMX512 standard. It has also been approved and recognized for ANSI standard classification.
Keeping Your LB-Par™ RGBW As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs! Weight & Dimensions Width 11.2 in (284 mm) Depth 4.5 inches (115.6 mm) Height 10.6 inches (269.5 cm) Weight 5 lbs (2.3 kg) Power Operating Voltage 100-240VAC, 50-60 Hertz Power Consumption 77W, .65A, PF: .99 Light Source LED 12* 10-watt 4-in-1 RGBW LEDs Optical Beam Angle Luminous Intensity 25 degree beam Lux/m Red Green Blue White All 1m 4,500 5,510 4,450 6,230 21,230 2m 1,540 1,810 1,450 2,050 6,460 Thermal Max. Operating Temp.
Dimensional Drawings 8.5 in (215 mm) 10.6 in (269.5 mm) 11.2 in (284 mm) 4.5 in (115.6 mm) 9.8 in (248.2 mm) DISCLAIMER: The power connector fitted to the fixture and fixture cord are designed for compatibility with products manufactured by Neutrik AG, Neutrik USA and their related entities, however they are not manufactured by, affiliated with or endorsed by Neutrik AG, Neutrik USA, or any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG.
Internal/External Parts # Name # Name 1. Upper housing cover 11. PowerCon™compatible input 2. Upper lamp pressing plate 12. Red PVC 3. Under lamp pressing plate 13. PCB-DMX canon socket 4. Lamps 14. Power supply 5. Copper pillar 15. Master PCB 6. PCB-lamp board 16. Outer bracket 7. Radiator 17. Knob 8. Copper pillar 18. Rubber gasket 9. 8015 fan 19. Inner bracket 10. PowerCon™ compatible input 20. Bottom housing cover Page 19 LB-Par™ RGBW User Manual Rev.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting
