Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS Stiletto™ Z19 Zoom Moving Head 1 1. Getting Started 3 What’s In The Box? Getting It Out Of The Box Powering Up! Getting A Hold Of Us Safety Instructions (Don’t Stick Your Hand In The Toaster!) 2. Meet The Stiletto™ Z19 Zoom Moving Head Features DMX Quick Reference The Stiletto™ Z19 Pin-up Picture 3.
1. GETTING STARTED What’s In The Box? • • • • 1 x Stiletto™ Z19 Zoom Moving Head An Ever-So-Handy Power Cord A Sweet Safety Cable & set of Mounting Brackets This Lovely User Manual Getting It Out Of The Box Congratulations on your purchase of the amazing Stiletto™ Z19 Zoom LED moving head.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2. MEET THE STILETTO™ Z19 ZOOM MOVING HEAD MAIN FEATURES • • • • • • • • • • • • 19 x 12.
Figure 1: The Stiletto™ Z19 Zoom Pin-Up Picture 4-in-1 RGBW LEDs Head/Arm LCD Readout Carry Handle Menu Buttons Figure 2: The Rear Connections DMX 3-pin In DMX 5-pin In DMX 5-pin Out DMX 3-pin Out Stiletto™ Z19 Beam Moving Head - Rev.
3. SETUP Fuse Replacement With a flat head screwdriver, wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type fuse. Insert the fuse holder back in its place and reconnect power. Connecting A Bunch of Stiletto Z19 Fixtures™ You will need a serial data link to run light shows using a DMX-512 controller or to run shows on two or more fixtures set to sync in master/slave operating mode.
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!) CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
Mounting Points Overhead mounting requires extensive experience, which includes calculating working load limits, knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Caution! Please be aware, you should have a qualified electrician performing all of your electrical connection needs.
Clamp Mounting This fixture provides a mounting bracket assembly that secures the bottom of the base, the “Omega Brackets,” and the safety cable rigging point together. When mounting this fixture to truss, be sure to secure an appropriately rated clamp to the omega bracket using an M10 screw fitted through the center hole of the “omega bracket”. 1.) Clamp 2.) Omega Bracket 3.
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the Stiletto™ Z19 Zoom are accessed by using the control panel on the front of the fixture. There are 4 control buttons below the LCD display which allow you to navigate through the various control panel menus. Button
Control Panel Menu Structure Main Function Sub Function Selection What It Does...
Control Panel Menu Structure (Continued) Main Function Sub Function Selection What It Does...
DMX Channel Values In-Depth (Continued) Short Mode Standard Mode Extended Mode 10 19 21 11 20 22 12 21 23 Channel Value 000 004 013 022 031 040 049 058 067 076 085 094 103 112 121 130 139 148 157 166 175 184 193 202 211 220 229 238 247 <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> <-> What it does 003 012 021 030 039 048 057 066 075 084 093 102 111 120 129 138 147 156 165 174 183 192 201 210 219 228 237 246 255 Macros No Functi
Photometric Data 7° Beam Angle 7° Beam Angle LUX (White) 0m 1m 51,300 @ 1m 2m 23,500 @ 2m 3m 4m 5m 11,000 @ 3m 6,600 @ 4m 4,600 @ 5m 900 @ 3m 500 @ 4m 400 @ 5m Photometric Data 50° Beam Angle LUX (White) 0m 1m 2m 3m 4m 5m 7,500 @ 1m 1,700 @ 2m Stiletto™ Z19 Beam Moving Head - Rev.
Troubleshooting Symptom Solution Fixture AutoShut Off Check the fan in the fixture. If it is stopped or moving slower than normal, the unit may have shut itself off due to high heat. This is to protect the fixture from overheating. Clear the fan of obstructions, or return the unit for service. Zoom is Dim Check optical system and clean excess dust/grime. Also ensure that the 220V/110V switch is in the correct position, if applicable.
5. APPENDIX A Quick Lesson On DMX DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre Technology (USITT) as a standardized method for connecting lighting consoles to lighting dimmer modules. It was revised in 1990 and again in 2000 to allow more flexibility. The Entertainment Services and Technology Association (ESTA) has since assumed control over the DMX512 standard. It has also been approved and recognized for ANSI standard classification.
Keeping Your Stiletto Z19 As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs! Weight & Dimensions Width 12.75 inches (325 mm) Depth 9.5 inches (240 mm) Height 16 inches (405 mm) Weight 22.04lbs (10 kg) Power Operating Voltage 110-240VAC 50/60Hz (autoranging) Power Consumption 300w, 1.05a, pf:.97 Light Source LED 19 x 12.8w 4-in-1 RGBW LEDs Optical Motorized Zoom 7° - 50° Movement Range Pan 540 degrees Tilt 270 degrees Thermal Max. Operating Temp.
This page left intentionally blank Stiletto™ Z19 Beam Moving Head - Rev.
This page left intentionally blank Stiletto™ Z19 Beam Moving Head - Rev.
This page left intentionally blank Stiletto™ Z19 Beam Moving Head - Rev.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting
