Manual

Page 12
RokPix Manual Rev. A © 2013 Blizzard Lighting, LLC
DMX Mode Allows the unit to be controlled by any universal DMX controller.
1.) The default mode for the fi xture is DMX, which appears as
d001 on the LED readout. To select
a different DMX address, using the <MENU> button, select
Addr,then hit <ENTER>. Use the
<UP/DOWN> buttons to select the correct address, then hit <ENTER> to confi rm.
Setting the DMX Channel Mode:
1.) To select a DMX channel mode, press the <MENU> button, then use the <UP> or <DOWN> buttons until the display reads
Chnd and press the <MENU> button. Then use the <UP> or
<DOWN> buttons until the display reaches your desired channel mode. Press the <MENU> button
to confi rm.
Stand-Alone, Master/Slave, Sound Active Modes: Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.
1.) To set the fi xture in Flash/Fade mode, select
FLAS or FAdE. To confi rm, press the <EN-
TER> button. 2.) Now, you can adjust the fl ash settings from
FL00-FL15 or the fade settings from FA00-
FA15.
Then press the <ENTER> button to confi rm.
3.) To use the fi xture in automatic mode, select
ASC-, and press the <ENTER> button. Then use
the <UP/DOWN> to choose from
AS00-AS15, then press the <ENTER> button to confi rm.
4.) Adjust the speed of the chase as above using
SP15 (slowest) to SP00 (fastest) then press the
<ENTER> button to confi rm. 5.) To set the fi xture as a slave unit, select
SLAU, and hit <ENTER>. The unit will display a fl ash-
ing
SL.AU to indicate it is in slave mode.
Sound Active Mode: 1.) To use sound active mode, select
SouA, then press the <ENTER> button. Then use the <UP/
DOWN> buttons to choose
Sou1 or Sou2. Press the <MENU> button to confi rm.
Standalone (Program) Mode: Allows a single unit to display a variety of colors and programs without a DMX controller.
1.) To set the fi xture in manual mode, select
Pr--. To confi rm, press the <ENTER> button.
2.) Now, select the program by using the <UP> and <DOWN> buttons to select
Pr00-Pr21. To
confi rm, press the <ENTER> button.
Pr00-Pr12 are static colors. Adjust the chase speed by
using the <UP> and <DOWN> buttons to navigate to
SP-- , and press the <ENTER> button.
Then select from SP00-SP15 (fast <--> slow).
Manual Color Adjustment: Allows the user to adjust the color balance of the fi xture. These settings are global, they will effect all modes.
1.) Use the <MENU> and <UP/DOWN> button to select
rL-- (Red Level), GL-- (Green Level),
bL-- (Blue Level) or UL-- (White Level), then hit <ENTER>.
2.) Using the <UP/DOWN> buttons, select the maximum level for each color between
x000-
x255
(000=off), then hit <ENTER> to confi rm.
Page 9
RokPix Manual Rev. A © 2013 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the fi rst fi xture. 2. Connect the end of the cable coming from the fi rst fi xture which will have a (female) 3 pin connec- tor to the input connector of the next fi xture con- sisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fi xture and so on.
A quick note: Often, the setup for Master- Slave and Standalone operation requires that the fi rst fi xture in the
chain be initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily, the fi xtures that follow may also re- quire a slave setting.
Check the “Operating Adjustments” section in this manual for com- plete instructions for this type of setup and confi guration. Mounting & Rigging This fi xture may be mounted in any SAFE position provided there is enough room for ventilation. It is important never to obstruct the fan or vents pathway. Mount the fi xture using a suitable “C” or “O” type clamp. The clamp should be rated to hold at least 10x the fi xture’s weight to ensure structural sta- bility. Do not mount to surfaces with unknown strength, and ensure properly “rated” rigging is used when mounting fi xutres overhead. Adjust the angle of the fi xture by loosening both knobs and tilting the fi xture. After fi nding the desired position, retighten both knobs. • When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance. • Safety cables MUST ALWAYS be used. • Never mount in places where the fi xture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation.