Instruction Manual

Page 11
ProPar Quadra LED Manual Rev. A Copyright (c) 2010 Blizzard Lighting, LLC
Control Panel Menu Structure
LED WASH
DMX512 Addr 001 <-- This is the starting menu position at power up.
Select Menu <>
DMX512 Addr 001 <-- Press <MENU> to reach this setting.
Display_OFF (YES/NO) <-- Press <DOWN> to reach this setting.
Press <ENTER> to change this setting,
then select value using <UP/DOWN>.
Press <ENTER> to confi rm.
Color Fade 000-255 <-- Press <DOWN> to reach this setting.
(Slowest <--> Fastest) Press <ENTER> to change this setting,
then select value using <UP/DOWN>.
Press <ENTER> to confi rm.
Color Change 000-255 <-- Press <DOWN> to reach this setting.
(Slowest <--> Fastest) Press <ENTER> to change this setting,
then select value using <UP/DOWN>.
Press <ENTER> to confi rm.
Color 00-15 <-- Press <DOWN> to reach this setting.
Press <ENTER> to change this setting,
then select value using <UP/DOWN>.
Press <ENTER> to confi rm.
00 Off 05 Yellow 10 Light Green 15 White (All)
01 Red 06 Cyan 11 White (All)
02 Green 07 Light Blue 12 Light Yellow
03 Blue 08 Magenta 13 Light Magenta
04 White Only 09 Pink 14 Light Cyan
Master Auto <-- Press <DOWN> to reach this setting.
Press <ENTER> to confi
rm.
Master Sound <-- Press <DOWN> to reach this setting.
Press <ENTER> to confi rm.
Slave 1-4 <-- Press <DOWN> to reach this setting.
Press <ENTER> to change this setting,
Each slave position will then select value using <UP/DOWN>.
allow the slaved fi xture to Press <ENTER> to confi rm.
repeat a different program.
Page 12
ProPar Quarda LED Manual Rev. A Copyright (c) 2010 Blizzard Lighting, LLC
DMX Mode
Allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page #15.
1.) The default mode for the fi xture is DMX, which appears as
DMX512 Addr 001on the LCD Readout.
Stand-Alone, Master/Slave, Sound Active Modes:
Allows a single or Master/Slaved units to run factory installed programs at user selectable
speeds.
1.) To set the fi xture in Flash/Fade mode, select
Color Fade or Color Change
To confi rm, press the <ENTER> button.
2.) Now, select the fl ash or fade speed using <UP> and <DOWN> buttons,
while the display reads
000 (slowest) to 255 (fastest), then press the
<ENTER> button to confi rm.
3.) To use the fi xture in automatic mode, select
Master Auto, then press
the <ENTER> button to confi rm.
Sound Acitve Mode:
1.) To use sound active mode, select
Master Sound.
2.) Press the <ENTER> button to confi rm.
Slave Mode:
1.) To use slave mode, select
Slave 1-4.
2.) Each slave setting will cause the slaved fi xtures to display another portion
of the auto/sound program. In other words, in a 4-light setup, the master will
display 1 color, while fi xtures 2/3/4 will display other colors depending on the
program.
3.) Press the <ENTER> button to confi rm.
Manual Mode (Color Preset Mode):
Allows a single unit to display a variety of colors without a DMX controller.
1.) To set the fi xture in manual mode, select Color.
To confi rm, press the <ENTER> button.
2.) Now, adjust the color by using the <UP> and <DOWN> buttons to select
00-15, using the color chart on page 12.
To confi rm, press the <ENTER> button.