Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS The Puck™ Q12 LED PAR Can 1 1. Getting Started 3 What’s In The Box? Getting It Out Of The Box Powering Up! Getting A Hold Of Us Safety Instructions (Don’t Stick Your Hand In The Toaster!) 2. Meet The Puck™ Q12 LED PAR Can 5 Features DMX Quick Reference (4 and 7-Channel Modes) The Puck™ Q12 Pin-up Picture 3. Setup 5 5 6 7 Fuse Replacement Connecting A Bunch Of Puck™ Q12 LED PAR Cans Data/DMX Cables 4.
1. GETTING STARTED What’s In The Box? • 1 x Puck™ Q12 Flat LED PAR Fixture • 1x IEC Power Cord • This Lovely User Manual Getting It Out Of The Box Congratulations on being completely and utterly qtastic! Now that you’ve got The Puck™ Q12 (or hopefully, Pucks!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2.
Figure 1: The Puck™ Q12 Pin-Up Picture Quad-Color LED’s LED Dual Mounting Yokes Ridiculously thin! Figure 2: The Rear Connections DMX In DMX Out AC Power In/Out LED Control Panel Microphone The Puck Q12A / Q12W Manual Rev.
3. SETUP Fuse Replacement With a flat head screwdriver, wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type fuse. Insert the fuse holder back in its place and reconnect power. Connecting A Bunch of Puck™ Q12 Flat LED PAR Cans You will need a serial data link to run light shows using a DMX-512 controller or to run shows on two or more fixtures set to sync in master/slave operating mode.
4. OPERATING ADJUSTMENTS NOTE: After making any adjustment, the fixture will return to the correct mode after approximately 5 seconds. DMX Mode Allows the unit to be controlled by any universal DMX controller. Addr 1.) The default mode for the fixture is DMX, which appears as on the LED Readout. Use the button then the and buttons to choose a channel between 1 and 512. Press again to confirm. 2.) To change between 3 and 6 channel DMX mode, select .
Troubleshooting Symptom Solution Fixture AutoShut Off Check the fan in the fixture. If it is stopped or moving slower than normal, the unit may have shut itself off due to high heat. This is to protect the fixture from overheating. Clear the fan of obstructions, or return the unit for service. Beam is Dim Check optical system and clean excess dust/grime. Also ensure that the 220V/110V switch is in the correct position, if applicable.
5. APPENDIX Keeping Your Puck™ Q12 As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs! Weight & Dimensions Length 8.25 inches (210 mm) Width 3.75 inches (95.25 mm) Height 7.5 inches (190 mm) Weight 4.2 lbs (1.9 kg) Power Operating Voltage 90-230VAC, 50-60 Hertz Fuse 3A 250V Power Consumption 56W Light Source LED 12x 10-Watt (4*2.5-watt) Quad-Color RGBA (Q12A) / RGBW (Q12W) LED’s 60K hrs. Optical Beam Angle 25 degrees 29 degree field Luminous Intensity Puck Q12A: 9,770 Lux @ 1m Puck Q12W: TBA Lux @ 1m Thermal Max. Operating Temp.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting
