PinUp TM Blizzard Lighting, LLC www.blizzardlighting.
TABLE OF CONTENTS PinUp™ 1 1. Getting Started 3 What’s In The Box? Getting It Out Of The Box Powering Up! Getting A Hold Of Us Safety Instructions (Don’t Stick Your Hand In The Toaster!) 2. Meet The PinUp™ LED 3 3 3 3 4 5 Main Features DMX Quick Reference The PinUp™ Pin-Up Picture 5 5 6 3.
1. GETTING STARTED What’s In The Box? • 1 x PinUp™ LED Pinspot • A totally rockin’ AC Power Cord • This Lovely User Manual Getting It Out Of The Box Congratulations on purchasing one of the coolest professional LED Pinspot fixtures anywhere! Now that you’re the proud owner of a PinUp™ (or hopefully, MORE!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition.
SAFETY INSTRUCTIONS • Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture.
2.
Figure 1: PinUp™ Pin-Up Picture Mounting Bracket Manual Focus Lens Locking Knobs Groovy Air Ventilation Openings Figure 2: The Rear Connections Unique Heatsink Design DMX Out DMX In Microphone LED Display The PinUp™ RGBW Pinspot Rev.
3. SETUP Fuse Replacement CAUTION! The PinUp™ utilizes a high-output switch-mode power supply with an internal fuse. Under normal operating conditions, the fuse should not require replacement. The fuse is field replaceable, however it is an advanced procedure suited to qualified individuals. Should your PinUp™ fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!) CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the PinUp™ are accessed by using the control panel on the rear of the fixture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.
Control Panel Menu Structure AOO1 A001 - 512 Sets the fixture DMX start address Run0 Run0 Run1 Run2 Run3 Run4 Run5 Run6 Run7 Run8 Run9 RunA RunB RunC Sou1 Sou2 Sou3 Sets the fixture to slave mode Red Custom Color Adjustment - (r000-255) r255 G255 b255 Y255 LEon LoFF LED display On/Off CoLr The PinUp™ RGBW Pinspot Rev.
DMX Mode: Allows the unit to be controlled by any universal DMX controller. 1.) The default mode for the fixture is DMX, which appears as A001 on the LED Readout. Use the button then the Up/Down buttons to choose a channel between 001 and 512. Press again to confirm. Setting up for Master/Slave: 1.) Use standard DMX cables to daisy chain your units together via the DMX connectors on the rear of the units. The first fixture in line from the DMX controller will serve as the Master. 2.
DMX Values In-Depth (6-Channel Mode) Channel Value What It Does 1 000 <--> 131 032 <--> 239 240 <--> 255 Dimmer (0% <--> 100%) Strobe (Slow <--> Fast) No Function 2 000 <--> 255 Red Intensity (0% <--> 100%) 3 000 <--> 255 Green Intensity (0% <--> 100%) 4 000 <--> 255 Blue Intensity (0% <--> 100%) 5 000 <--> 255 White Intensity (0% <--> 100%) 6 000 003 032 064 080 096 112 129 144 160 176 192 208 224 No Function Run 1 Program Run 2 Program Run 3 Program Run 4 Program Run 5 Program Run 6 Pr
5. APPENDIX Keeping Your PinUp™ As Good As New The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. You should absolutely keep the fixture clean, especially if you are using it in an environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Tech Specs! Weight & Dimensions Length 2.63 inches (66.41 mm) Width 4.75 inches (120.18 mm) Weight 0.9 pounds (66.41 kg) Power Operating Voltage 90-230VAC, 12VDC 2.0A Current 1.0A Light Source LED 1* 10-watt RGBW LED, 100,000 hours Optical Beam Angle 6° Luminous Intensity 1200 Lux/1m Thermal Max. Operating Temp.
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting
