Owner's manual
DATA AC / WG
- SBC I-D is capable of displaying up to 3 -
A
C - Actuator Type Wastegate
DATA
different optional displays Capable of
WG External Type Wastegate
DATA
diff
eren
t
op
ti
ona
l
di
sp
l
ays.
C
apa
bl
e o
f
-
WG
-
E
x
t
erna
l
T
ype
W
as
t
ega
t
e
displaying electronic outputs from - Refer to Page 3 and 4 for different types of wastegate
INPUT LINE 1 the ECU such as temperature, voltage, - To set, press MENU and go to Main Menu. Scroll to AC / WG,
LOW [ V ] 0.0 pressure, TPS, A/F, and etc. press enter and scroll to select. Press enter to set.
FIT 0.00 - Optional harness is needed to display
HIGH
[
V
]
5.0 this feature.
UNIT
HIGH
[
V
]
5
.
0
this
feature
.
UNIT
FIT 1.00 - SBC I-D has the ability to display 4 different types of boost pressure
UNIT %
kg/cm
2 -76 cmHG ~ 2.50 kg/cm2
kpa -76 cmHG ~ 2.45x100 kpa
DAT
A
* To set up A/F, set up DATA BAR -30 inHG ~ 2.45 BAR
chart as shown below. PSI -30 inHG ~ 35.5 PSI
INPUT LINE
2
To set press MENU and go to Main Menu Scroll to Unit and
INPUT
LINE
2
-
T
o se
t
, press
MENU
an
d
go
t
o
M
a
i
n
M
enu.
S
cro
ll
t
o
U
n
it
an
d
LOW [ V ] 0.0 LOW [ V ] 0.00 press enter. Scroll left or right to select Unit, press enter to set.
FIT 0.00 FIT 0.00
HIGH [ V ] 12.0 HIGH [ V ] 16.0
CONTRAST
FIT 200 FIT 16.0 - To set, press MENU and go to Main Menu. Scroll to CONTRAST
UNIT *C UNIT VOLT and press enter. Scroll to adjust, press enter to set.
pj,p
DAT
A
BRIGHT
- To set, press MENU and go to Main Menu. Scroll to BRIGHT
INPUT LINE 3 Important and press enter. Scroll to adjust, press enter to set.
LOW [ V ] 0.0 - Addition instructions are included in the
FIT
000
SBC I
-
D optional harness
RESET
FIT
0
.
00
SBC
I
-
D
optional
harness
.
RESET
HIGH [ V ] 16.0
FIT 16
UNIT Volt
ALL
RESET
AUTO PEA
K
Auto Peak ON - Will automatically reset Peak Hold. Peak will
reset only when throttle is release after the vehicle -> EXECUTE
has been in boost for more then 2 seconds. CANCEL
Auto Peak OFF - Peak Hold will retain the highest boost level
achieved. 1 Press MENU button
,
scroll down to RESET and
p
ress
RESET
achieved
.
1
Press
MENU
button
,
scroll
down
to
RESET
and
press
- To set Auto Peak, Press MENU and go to Main Menu. Scroll to enter to select.
Auto Peak, press enter and scroll to select. Press enter to set. 2 To select function, scroll down and press enter.
- To reset Peak hold, press both REC/STOP and MENU button at once.
NOTE: It is recommended to reset the boost controller
if the unit is not functioning properly.
Page 9
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes
Online Manual Not For Resale Purposes