user’s manual BZE-10A Half–DIN 10 Band Slide Control Pre-Amp Equalizer with Subwoofer Boost Control
INTRODUCTION... Thank you for purchasing the Blitz Graphic Equalizer. Rest assured you have purchased a quality product designed and engineered to give YOU many years un-compromised musical service. The Blitz Graphic Equalizer has been designed using the latest in electronic technology available today. When you check the list of features offered by the BZE-10A, you’ll know you made the right choice with a Blitz Graphic Equalizer network.
table of contents general features 2 precautions 3 features and specifications mounting and installation system wiring troubleshooting 4-5 6 7-8 9
general features · 10 Band Graphic Equalizer · Rotary Subwoofer Boost Control with Active Electronic Adjustable Crossover · Rotary Fader Control · Full Night Illumination · Compact 1/2 DIN Chassis Size · Front Panel DVD Input Jack · 2 RCA Input Jacks · 6 RCA Signal Output Jacks (2 Front/2 Rear/ 2 Subwoofer) · Electronic Crossover Adjustable to 80, 120 or 160Hz @12dB · Frequency Response: 20Hz–20kHz 2
Precautions Never drive with the volume raised so high you cannot hear what is occurring in traffic around you, Be aware that repeated exposure to excessive volume levels can permanently damage your hearing! Keep all electronics away from moisture, dust, extreme heat or extreme vibrations. Blitz Audio products are capable of sound pressure levels in excess of 150dB. Continuous exposure to sound pressure levels over 100 dB may cause permanent loss of hearing. Use common sense and PRACTICE SAFE SOUND.
features and specifications Fader 30 Hz Subwoofer 60 Hz 120 Hz 250 Hz 500 Hz 1 kHz 2 kHz 4 kHz 8 kHz 16 kHz 10 DEF 0 PWR DVD F R MIN 10 MAX 4 SUB REAR FRONT LINE INPUT 80 120 L R 160 Hz L R L R L R
features and specifications 1 fader control 2 subwoofer output control Rotary mechanism to control the balance between the front and rear speakers. This fader will override the fader in your car stereo. Rotary mechanism to control the amount of subwoofer gain at the predetermined crossover point. The subwoofer can be adjusted from minimum to maximum by turning the knob.
Mounting and installation The BZE10A is a Half DIN sized unit. It can be mounted in the dashboard with your head unit in most cases. Use of an auxiliary installation kit is needed like those made by American international or Scoche products. The BZE10A is also supplied with mounting brackets giving you the option to mount the equalizer under your dash, or on the console or in your glove compartment. There are three power wires coming out of the back of the unit.
System wiring Diagram A for RCA input configuration If your radio does not have RCA output jacks as in the case of most standard OEM radios you can use the speaker outputs from those head units to power the BZE10A by interfacing them with a high/low level impedance adaptor like the Pyramid Model NS60 or any of the other numerous models available.
System wiring Diagram C for sample amplifier installations Diagram C 8 Diagram D for wiring directions Diagram D
Troubleshooting PROBLEM POSSIBLE CAUSE Signal processor does not turn on. • Remote turn-on wire has 12V. • 12V wire has 12V • Ground wire is properly connected Level of sound is low. • Wiring is not loose or cables misconnected/disconnected • RCA cables are not faulty. Background noise is too high. • Wiring is not loose or cables misconnected/disconnected • RCA cables are not faulty.
limited warranty policy E q u a l i z e r All Blitz products are carefully constructed and thoroughly tested before shipment. Products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Blitz.
