DESIGNER SERIES OWNER’S MANUAL AND USER GUIDE
TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFEGUARDS �����������������������������������������������������������1 SECTION 2 - UNPACKING ������������������������������������������������������������������������������������������������3 SECTION 3 - GETTING TO KNOW YOUR BLENDER ��������������������������������3 SECTION 4 - INSTALLATION �������������������������������������������������������������������������������������������4 SECTION 5 - OPERATIONAL OVERVIEW ������������������������������������������������������
SECTION 1: IMPORTANT SAFEGUARDS IMPORTANT INFORMATION Read all instructions carefully before using your Designer series blender. Following these instructions will help prevent injuries and damage to the machine and will ensure that you have the best possible experience with your Designer series blender. 1.1 AVOID CONTACT WITH MOVING PARTS • ALWAYS keep fingers, hands, hair and clothing away from all moving parts.
1.8 BLADES ARE SHARP! HANDLE CAREFULLY! 1.9 WARNING, DO NOT BLEND HOT LIQUIDS OR OTHER HOT INGREDIENTS Starting blend cycles with boiling or very hot liquids may result in burns or cause the lid to blow off. 1.10 USE CAUTION WHEN BLENDING ON THE SOUP CYCLE When blending on the Hot Soup cycle, friction of the blade will heat the contents. The vented lid will allow pressure relief. Be careful not to come in contact with any steam coming from the clear center lid. 1.
SECTION 2: UNPACKING SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE 2.1 UNPACKING YOUR BLENDER You should have received the following items: • Designer series blender motor base • Blender jar with lid • Blendtec 101 booklet • Customer Service and Warranty Registration Card Additional literature may be included depending on package configuration 1. Remove blender motor base, blender jar, and lid from packaging. 2. Unwind the power cord. 3.
3.2 BLENDER JAR ASSEMBLY The blender jar assembly consists of the blender jar, blade assembly, and lid. • Jar: Durable, BPA-free jar; easy to clean. • Blade Assembly: Uniquely designed stainless steel blade provides fast, consistent blending. • Lid: Vented gripper lid seals liquids within the jar during blending. NOTE: Filling the blender jar beyond the marked capacity is not recommended. SECTION 4: INSTALLATION 1. Place the blender on a flat, clean, and dry surface.
FIGURE 1: BLENDER JAR ASSEMBLY Lid Clear Vented Cap Insert Plunger-Free Easy-Clean Jar Blade Assembly The jar shown above is the Wildside+™ Jar FIGURE 2: MOTOR BASE Hardened Metal Drive Socket LED Information Center Smart Touch Interface Motor Base Cover Power Cord located in back Power Unit 5
SECTION 5: OPERATIONAL OVERVIEW 5.1 QUICK RECIPE INSTRUCTIONS – Use these steps to get started right away. 1. Choose a recipe from the included Blendtec Blending 101 booklet. 2. Gather all of the ingredients. 3. Load the blender jar as indicated in the recipe. 4. Plug in the blender. 5. Press the power button located on the upper right hand side of the smart touch interface. 6.
5.3 DESIGNER 600 SMOOTHIE This cycle is designed specifically for various types of smoothies and thick drinks that frequently use dense or frozen ingredients. It slows down and speeds up automatically during the course of the cycle. This allows the blender to draw the ingredients into the blending vortex, creating the desired texture. To use the Smoothie cycle, load your jar as indicated in the recipe you are using, secure the lid, and press the Smoothie icon.
5.4 DESIGNER 625 SMOOTHIE This cycle is designed specifically for various types of smoothies and thick drinks that frequently use dense or frozen ingredients. It slows down and speeds up automatically during the course of the cycle. This allows the blender to draw the ingredients into the blending vortex, creating the desired texture. To use the Smoothie cycle, load your jar as indicated in the recipe you are using, secure the lid, and press the Smoothie icon.
The Pulse setting runs at speed 7 and will only run while the Pulse remains pressed. When the icon is released, the motor shuts off. icon CAPACITIVE TOUCH SLIDER The capacitive touch slider allows you to fine-tune the speed of your blender. Simply slide your finger to the right to increase the blender’s speed or the left to decrease speed. 5.5 DESIGNER 675 +10 This +10 icon allows users to add 10-second intervals to their blend cycles. It also acts as a stand-alone, 10-second cycle.
HOT SOUP This cycle is designed for hot recipes. The cycle’s length of time, combined with the speed of the motor, heats the ingredients to a hot temperature. This cycle can also be used for hot chocolate, syrups, and fondue. When using fresh ingredients, remember that the speed of the blade generates enough heat to warm the ingredients Do not add any liquids or ingredients over 115° F to the jar when preparing soups or hot items. CLEAN This cycle that automatically cleans the inside of your blender jar.
To use the Smoothie cycle, load your jar as indicated in the recipe you are using, secure the lid, and press the Smoothie icon. The blender will run the cycle and automatically shut off. DIPS This cycle stays at relatively low speeds for shorter periods of time. This combines your dips, allowing the flavors to blend together properly, without over-mixing. To use the Dips cycle, load your jar as indicated in the recipe you are using, secure the lid, and press the Dips icon.
PULSE The Pulse function is used for chopping, mincing, whipping, or other momentary tasks that do not require a long blend cycle. You can also Pulse to quickly stir a blend before serving. The Pulse setting runs at speed 7 and will only run while the Pulse remains pressed. When the icon is released, the motor shuts off. icon CAPACITIVE TOUCH SLIDER The capacitive touch slider allows you to fine-tune the speed of your blender.
WHOLE JUICE This cycle is designed to completely blend tough and dense ingredients, including carrots, celery, and seeds. Use the Whole Juice cycle if you are using any fruits and/or vegetables with stems, seeds, or skins. When blending carrot juice or other dense juices, you may need to repeat this cycle once or twice until the desired texture and consistency are achieved. HOT SOUP This cycle is designed for hot recipes.
5.8 ORIGINAL DESIGNER SERIES BATTERS This cycle stays at relatively low speeds for shorter periods of time. This combines your dips, allowing the flavors to blend together properly, without over-mixing. To use the Batters cycle, load your jar as indicated in the recipe you are using, secure the lid, and press the Dips button The blender will run the cycle and automatically shut off. MIXED DRINKS This cycle is used for mixed drinks, milkshakes, iced coffees, and milkshakes.
HOT SOUP This cycle is designed for hot recipes. The cycle’s length of time, combined with the speed of the motor, heats the ingredients to a hot temperature. This cycle can also be used for hot chocolate, syrups, and fondue. When using fresh ingredients, remember that the speed of the blade generates enough heat to warm the ingredients Do not add any liquids or ingredients over 115° F (46° C) to the jar when preparing soups or hot items.
3. BLENDER JAR IS DISHWASHER SAFE—TOP RACK ONLY! 4. Extreme temperatures damage the lower seal of the jar. We recommend handwashing to prolong the life of the blender jar. We do not recommend the jar be used or exposed to, temperatures above boiling (212°F, 100°C). SECTION 7: TROUBLESHOOTING While we don’t expect you to have any problems with your blender, sometimes failures do occur. Use the following guidelines to see if the problem is easily fixed or requires service. 7.
7.3 NOISE LEVEL CHANGES If the blender noise level has increased from original levels, determine whether the sound is coming from the blender motor or jar. 1. Blender motor: Remove the jar, and press Pulse .Listen to the motor. If it is excessively noisy, please contact your Blendtec Service Agent for evaluation. 2. Jar: After checking the motor, fill the jar with 2 cups of water and place back on the motor base. Run the blender for a few seconds by pressing the Pulse button.
THIS WARRANTY APPLIES ONLY TO PRODUCTS SOLD BY BLENDTEC OR ITS AUTHORIZED DEALERS LIMITED WARRANTY Blendtec warrants the blender motor to be free of defect in material and workmanship for the warranty period. During this period, such defects will be repaired or the product replaced at Blendtec’s discretion without charge. This warranty does not cover damage caused by misuse, accident, or negligence.
Your Name: ��������������������������������������������������������������� Address: ������������������������������������������������������������������ Phone Number: ������������������������������������������������������������ Motor Serial #(Found on bottom of motor base): �������������������������������� Cycle Count (From the LED Information Center): ��������������������������������� Your Purchase Date: �������������������������������������������������������� Place of Purchase: ����������������������
1206 SOUTH 1680 WEST OREM, UTAH 84058 U.S.A. 1-800-BLENDTEC BLENDTEC.COM 20 ©2014 K-TEC, INC., ALL RIGHTS RESERVED BLENDTEC IS A REGISTERED TRADEMARK OF K-TEC, INC. ed. OWN-RD-210 MANUAL, DESIGNER of K-TEC,SERIES, Inc.
