User Guide

ManualsBrandsBlendtec ManualsBlendersBlendtec C600A0801-A1GA1A Chef 600 Commercial Blender, Black

COMMERCIAL

SERIES

OWNER’S MANUAL AND USER GUIDE

Summary of content (19 pages)

PAGE 1
COMMERCIAL SERIES OWNER’S MANUAL AND USER GUIDE
PAGE 2
TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFEGUARDS ��1 SECTION 2 - UNPACKING ��3 SECTION 3 - GETTING TO KNOW YOUR BLENDER ��3 SECTION 4 - INSTALLATION & OPERATIONAL OVERVIEW ��4 4.1 - STEALTH 875™ & STEALTH 885™ ��4 4.
PAGE 3
1.7 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD BY BLENDTEC The use of any unauthorized attachments may cause fire, electric shock, and/or injury and will void the warranty. SECTION 2: UNPACKING SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE 2.1 UNPACKING YOUR BLENDER You should have received the following items: 1.8 BLENDER JAR MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS OPERATING • Commercial series blender motor base 1.
PAGE 4
3.2 BLENDER JAR ASSEMBLY The blender jar assembly consists of the blender jar, blade assembly, and lid. These components are integrated to ensure consistently blended drinks and greater operator safety. 24 ⅜” (62 cm) • Lid: The lid seals liquids within the jar during blending. Some models have a vent that provides pressure relief when blending hot foods. • Jar: Your jar is durable, BPA-free, and easy to clean.
PAGE 5
• If installing more than one blender, allow 14”–16” (35.6 - 40.6 cm) of center-to-center blender spacing. • If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the sound enclosure to the wall and 26” (66 cm) from the countertop to any over-thecounter cabinetry. • Ensure lower cabinetry allows adequate airflow.
PAGE 6
Multipurpose Profile* Button 1: Small Milkshake Button 2: Granita / Medium Milkshake Button 3: Small Margarita / Ice Cappuccino Button 4: Medium Smoothie 4 Button 5: Large Smoothie 4 Button 6: 50 Seconds @ Speed 7 *When you turn the blender on for the first time this will be the default profile.
PAGE 7
4.1.7 Selecting the Desired Profile 1. Press and hold the cancel/exit button for 3 seconds. 2. Select Profiles from the menu by touching the select button. 3. Use the scroll and select buttons to select either the Standard Profiles or Custom Profiles category. 4. After selecting the Standard or Customer Profile category, you can scroll through the profiles in the category and select the desired profile. 5. “Make this the active profile?” will appear on the screen.
PAGE 8
Secure Blender Feature When creating or modifying a profile via the Blend Wizard, one of the options is to secure the blender. If you select this option, once you have downloaded the profile to a USB drive and then imported the profile to the blender, some of the advanced programming functions will be disabled.
PAGE 9
Blend Cycle Pause When in automatic mode, this setting allows you to pause and resume a blend cycle at the same time and speed. To enable or disable the Blend Cycle Pause feature, complete the following steps: 1. Press and hold the cancel/exit button for 3 seconds. 2. Use the scroll button and then select Settings from the menu by touching the select button. 3. Use the scroll button and then select Blend Cycle Pause from the menu by touching the select button. 4.
PAGE 10
4.2 CONNOISSEUR 825™ 4.2.1 Installation Connoisseur 825 Above Counter Installation • Select a location that is near an electrical outlet. Also consider proximity to ingredients, and patrons as well as available counter space. • Place the blender on the counter in a spot where the air intake vents on the sides and exhaust on the back of the blender are unobstructed. • Ensure there is enough room above and around the unit to allow for unhampered movement of the sound enclosure (see Figure 4 for measurements).
PAGE 11
Automatic Cycle Operation In-Counter Installation • Feed the electrical cord through the hole in the countertop. Your Connoisseur blender is preprogrammed with multiple blender profiles, to help operators achieve consistent blends with a minimum of training, trial and error. • Gently place the blender unit into the hole. • Ensure the gasket is seated correctly, lying flat against the counter surface and not pinched by the housing. • Plug the unit into an outlet with appropriate electrical protection.
PAGE 12
4.3 CHEF 775™ Quick Start Guide 1. Touch the power icon to turn on the blender. 2. Place the blender jar on the motor base, ensuring the jar is completely seated and the jar lid is secured. 3. On the control surface, touch the desired blend cycle icon, pulse icon or desired location on the slider control bar. 4. Touch the cancel/exit icon to stop a blend cycle or manual operation before the programmed time elapses.
PAGE 13
4.4 EZ 600™ Quick Start Guide 1. Toggle the power switch on the back of the motor base. 2. Place the blender jar on the motor base, ensuring the jar is completely seated and the jar lid is secured. 3. On the control surface, touch the desired blend cycle icon or pulse icon. 4. Push any blend cycle button to stop a blend cycle before the programmed time elapses. EZ 600™ EASY-CLEAN JAR Blender Modes The EZ 600 includes three profiles that can be changed when first turning on the blender.
PAGE 14
4.5 CHEF 600™ Quick Start Guide 1. Toggle the power switch on the back of the motor base. 2. Place the blender jar on the motor base, ensuring the jar is completely seated and the jar lid is secured. 3. On the control surface, touch the desired speed setting. Interface All manual speeds count up to 90 seconds then stop. To stop a blender cycle before the 90 seconds elapses, press the Stop button.
PAGE 15
SECTION 5: CARE AND CLEANING 5.1 CLEANING AFTER USE 1. Add hot water and 1-2 drops of liquid dish soap to the blender jar. 2. Place the lid tightly onto the jar, place the jar on the motor base and press and hold the pulse button for 5-10 seconds. 3. Rinse all soap from the jar and lid with water. 4. If the jar is stored upside down, shake excess water from the jar after cleaning. Note: WildSide+™ and FourSide™ jars can be stacked to save space. 5.2 LONG-TERM SANITATION 1.
PAGE 16
CONNOISSEUR 825™ Overtemp Error — This indicates that the motor is overheating. The blender has been disabled until the unit cools to operating temperatures. If the blender does not work after 20 minutes or more of cooling time, please call your Blendtec Service Agent. Overtemp Error — This indicates that the motor is overheating. The blender has been disabled until the unit cools to operating temperatures.
PAGE 17
6.5 UNRESPONSIVE CONTROL SURFACE If the control surface of your blender is not responding, wipe it down with a damp rag to remove any liquids or particle buildup. If that doesn’t work, unplug the power cord and then plug it in again. INSTRUCTIONS THAT APPEAR IN THIS USER GUIDE ARE NOT MEANT TO COVER EVERY POSSIBLE CONDITION OR SITUATION THAT MAY OCCUR. GOOD JUDGMENT MUST BE USED WHEN OPERATING THIS OR ANY OTHER MACHINERY. SECTION 7: WARRANTY 7.
PAGE 18
FORM TO SEND WITH BLENDER FOR REPAIRS/REPLACEMENT (Please make a copy of this form.