operations manual for the: ABC Smoother and SpaceSaver BRAWN. BRAINS. BLENDTEC.
Table Of Contents Section Page Section 1.....Important Safeguards 1 Section 2.....Component Overview 3 Section 3.....Unpacking 5 Section 4.....Installation 6 Section 5.....Operating Instructions 9 Section 6.....Warranty and Service 13 Appendix A.....ABC Operation A-I Appendix B.....
SECTION 1 – IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS CAREFULLY BEFORE USING YOUR BLENDTEC MACHINE. 1.1 SAFETY CERTIFICATION The ABC, Smoother, and SpaceSaver blenders and accessories are certified by ETL to UL standard 763, by CSA standard C22.2 No. 195-m1987, and to CE Standards. 1.2 HEALTH CERTIFICATION The ABC, Smoother, and SpaceSaver blenders and accessories are certified by NSF International. R 1.
1.7 THE 110/120 VOLT RECEPTACLE FOR EACH POWER UNIT MUST BE PROTECTED BY A SEPARATE 20 AMP CIRCUIT BREAKER OR FUSE. THE 220/240 VOLT RECEPTACLE FOR EACH POWER UNIT MUST BE PROTECTED BY A SEPARATE 13 AMP CIRCUIT BREAKER OR FUSE. Do not use any other electrical equipment on the same circuit as the blender or you risk overloading the circuit and either damaging the blender electronics or blowing the circuit protection. 1.
2.5 POWER SPECIFICATIONS SECTION 3: UNPACKING Blendtec Blenders are made with power specifications listed below according to your specific model. 110/120 VOLT BLENDTEC BLENDERS ARE REQUIRED TO BE PROTECTED BY A DEDICATED 20 AMP CIRCUIT BREAKER OR FUSE.
SECTION 4: INSTALLATION 4.1 Above Counter Installation (For SpaceSaver model, disregard mention of polycarbonate sound enclosure) 1. Insure that an electrical receptacle is readily accessible when you locate the equipment. ● If installing a sound enclosure, allow a clearance of at least 8 1/2 in. (216 mm) from the sound enclosure to the wall and 26 in. (660 mm) from the counter top to any over-the-counter cabinetry. ● Ensure lower cabinetry allows adequate airflow. There should be at least 8 1/8 in.
5. Carefully re-install the sound enclosure lid using the stainless steel hinge pin. Never drop or slam enclosure lid. 6. Plug the unit into a receptacle with appropriate protection. Make sure power switch is turned off before plugging unit in. SECTION 5: OPERATING INSTRUCTIONS 5.1 OPERATIONAL OVERVIEW 1. Raise the enclosure lid. If blender is not turned on, turn on the main power switch located on the front of the blender motor. 2.
A reading of “OVERLOAD” indicates an overload on the motor. Turn the motor off for 10 seconds (using the switch) then turn the motor on again to clear the overload condition. Check the blender jar for blockage. A reading of “LOW VOLTAGE” indicates not enough voltage coming to the motor. Turn the motor off. Correct the cause of low voltage. (Normally caused by more than one appliance drawing power on the same circuit, or by low power from a power source {brown out}.
5.7 DAILY CLEANING OF MOTOR 1. Make sure the main power switch is off and motor is unplugged before cleaning. SECTION 6: WARRANTY AND SERVICE PROCEDURE 2. Remove motor from sound enclosure. Remove the rubber gasket from the rim of the steel base and wash the gasket with a mild detergent. MOTOR: Standard Blendtec United States (US) warranties are as follows: 3. When necessary, wipe the metal top and sides of the blender motor clean with a damp rag. Mild cleaners like WINDEX® may be used. 5.
6.2 SERVICE PROCEDURE Should you experience any difficulty in using your Blendtec blender, please do the following: UNDER WARRANTY 1. Contact your authorized Blendtec service agent immediately to diagnose the difficulty. Please have your serial number ready as well as a description of the problem. Do not attempt to do your own repairs. Repairs made by persons other than Blendtec authorized service representatives will void the warranty. Many issues can be resolved simply and quickly over the phone. 2.
5.84” Lid 8.31” Jar Blade Assembly 8.31” SIDE VIEW FRONT VIEW FIGURE 1.2 - TOP VIEW: MOTOR 8.81” Power Switch 17.12” LCD Screen SIDE VIEW (OPEN ENCLOSURE) FIGURE 1.1 - FRONT VIEW: BLENDER MOTOR AND JAR 28.815” FIGURE 2.1 - ABOVE COUNTERTOP: TITAN, ABC, SMOOTHER APPENDIX B - PRODUCT DIAGRAMS Touchpad Page A-II 17.
SIDE VIEW 8.22” 16.09” SIDE VIEW (OPEN ENCLOSURE) FIGURE 2.3 - ABOVE COUNTERTOP: SPACESAVER Page A-IV FRONT VIEW 18.41” 6.32” SIDE VIEW FRONT VIEW 16.09” 9.35” 9.29” 18.41” 9.35” 2.59” 22.51” FIGURE 2.
Page A-VI FRONT VIEW 8.49” SIDE VIEW 8.97” SIDE VIEW FRONT VIEW 10.24” 9.19” 8.50” 10.97” 10.24” 10.97” 3.03” SIDE VIEW (OPEN ENCLOSURE) 8.00” 14.37” 6.02” SIDE VIEW (OPEN ENCLOSURE) 8.00” 22.67” FIGURE 3.1 - IN - COUNTER: TITAN, ABC, SMOOTHER FIGURE 3.
FIGURE 4 - Countertop Hole Template 5 ⅞” 4 ⅜” PageA-VIII Page A-IX
1206 South 1680 West Orem, UT 84058 801-222-0888 www.blendtec.com OWN-010 Manual for Titan, ABC, Smoother, and SpaceSaver Rev.
