Manualshelf

Owner's Manual

ManualsBrandsBlendMount ManualsGPS & car accessoriesCustom-Fit Radar Detector Mount
12
PART# BBE-2017
Blend
fflount-
®
ESCORT.
BELTRONICS.
11
11
1
1111
11
111
11
1111
1111
111
11
1
Innovative
Mounting
Solutions
LEFT HAND
DRIVE
VEHICLE
7
28028
1
9702
a
INSTALLATION
INSTRUCTIONS
FOR BELTRONICSAND
ESCORT
RADAR
DETECTORS
Your rear
view
mirror
has minimal clearance between
the
back
side
of
the
mirror
and the
mirror
stem.
It
is
very
important
that
this
mount
Is Installed correctly
to
ensure
mirror
adJustablllty
Is
retained.
PLEASE READ
THESE
INSTRUCTIONS
THOROUGHLY
BEFORE
INSTALLING
THIS
MOUNT
NOTE:
For
Illustration
purpoau,
the
mount
and
rear
view
mirror
shown
In
thffe
lnatructlona
may
look
allghtly
different
then
YOUR
mount
and
rear
viaw
mirror.
RELEASE BUTTON
89fore
lnstalllng
this
mount
on
your
mirror
observe
how
the spring clip functions.
When
used
property,
the
spring
cllp
avoids
putting
excessive
prwuure
on
the
mirror
when
lnstalllng
and
removing
the
radar
detector
(RD),
To
release tension from the spring clip, simply squeeze the tab and
the back side
of
the mount together. This wlll lower the bottom portion
of
the
spring clip allowing you ID allele
the
RD
on
and
off
the
mount. Push the
RD
Releaee button and slide
the
RD
onto the Spring Cllp unlll
you
hear
It lock Into position, then release both the Tab and Release Button. Install and
remove the
RD
a
few
times before lnatalllng
the
mount
on
your
mirror.
Once
th•
lnatallatlon
la
complate,
th•
aprlng
cllp
allows
you
to
accua
th•
buttons
on
top
of
tha
RD
whil•
still
having
the
RD
installed
to
sit
as
cloaa
to
th•
bottom
of
th•
rear-viaw
mirror
as
poasibla.
By
gently pushing
down
on
the
RD
the spring clip is designed
to
flex downward allowing you
to
push desired buttons, then it will spring back into its original position when
you 'lake your finger away. This can also
be
usefull
1D
access the release button.
STEP 1 • Loosen
the
clamp screw
so
the
kip
section &eperates from
the
mid section. This wlll
prwlde
the necessary clearance to slide the
mount
over
the
mirror stem
as
shown above. AdJuat
the
mirror
paralell
to
the
windahiald
and
•lightly
upward
for
Nila
of
installation.
TOPANDMID
SECTIONS MUST TOUCH
A.T
THE PIVOT POINT
BEFORE CLAMP SCREW
IS
FULLY
TIGHTENED
CLEARANCE /
FORMIRROR
~
STEM
PIVOT POINT
STEP 2 • BEFORE
FULLY
TIGHTENING THE
CLAMP
SCREW,
MAKE
SURE THE TOP
AND
MID
SECTIONS
ARE
TOUCHING
A.T
THE
PIVOT POINT.
If
you
can
not
get
them
to
touch
at
the
pivot point,
you
have
an
incompatibla
mirror
typa for this
mount
PA.GE
1
OF2

Summary of content (2 pages)