Owner's Manual
Table Of Contents
- USE & CARE GUIDE
- ATTENTION:
- I. Safety and Installation Warnings 4-7
- II. Location of Appliance 8-9
- i. Electrical Safety and Installation Warnings 10-11
- III. Gas Safety and Installation Warnings 11-12
- IV. Gas Leaks 13
- i. Checking for Gas Leaks 13-15
- ii. Unpacking Unit 15-16
- V. Gas Connections 16
- i. Natural Gas Requirements 16
- ii. Liquid Propane Gas and Tank Requirements 16-18
- iii. Transporting and Storing LP Gas 17-18
- VI. Installing the Appliance in an Island 19-22
- i. Outdoor Kitchen Ventilation 20-21
- ii. Building Specifications + Instruction 21-23
- iii. Installation Diagrams 23-24
- VII. First Time Operation 25
- i. Lighting the Appliance 25-26
- ii. Manually Lighting the Appliance 26-27
- iii. Flame Adjustment 27
- VIII. Cleaning your Appliance 28-29
- IX. Fuel Conversion 30-32
- Do not attempt to heat unopened containers on the griddle as pressure may build up and cause the container to explode.
- Never use charcoal or any other solid fuel in the griddle.
- Never cook without the drip pan in place.
- Never operate this griddle while under the influence of alcohol or drugs.
- Never place your fingers inside the observation openings in the griddle plate during removal or replacement of the griddle plate as they could be pinched. Never place your fingers inside the observation openings in the griddle at any time as injury co...
- Location of Appliance
- Gas Safety and Installation Warnings
- IMPORTANT: Never connect the appliance to an unregulated gas supply.
- Installation must conform with local codes or in the absence of local codes, to the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and Natural Gas Installation Code, CSA B149.1. All Natural Gas installations must conform to local codes or in the absence ...
- Leak Testing
- NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS.
- Never place your fingers inside the observation openings in the griddle plate during removal or replacement of the griddle plate as they could be pinched. Never place your fingers inside the observation openings in the griddle at any time as injury co...
- Never place your fingers inside the observation openings in the griddle plate during removal or replacement of the griddle plate as they could be pinched. Never place your fingers inside the observation openings in the griddle at any time as injury co...
- Natural Gas Requirements
- Liquid Propane (LP) Gas and Tank Requirements
- Installing the Appliance in a BBQ Island
- FIRST-TIME OPERATION
- Cleaning Your Appliance
- Fuel Conversion
- Warranty Registration
- Improper Maintenance, high cooking temperatures, excessive humidity, chlorine, fertilizers, lawn pesticides, chemicals, and salt can affect the Stainless Steel components and for these reasons, the warranties DO NOT COVER DISCOLORATION, SURFACE RUST, ...
- Locating the Product Serial Number:
- Blaze Product Registration
- Blaze Outdoor Products, Warranty Registration, 6620 Greenwell Springs Rd.
- Baton Rouge, LA 70805
Blaze Outdoor Products Instructional Book
Page | 18
Procedure for LP Gas Cylinder Connection (20 lbs)
The LP Gas Cylinder must be in compliance with the specifications for LP‐Gas Cylinders of the US
Department of Transportation or the National Standard of Canada, CAN/CSA‐ B339. The basic tank size
is 12” in diameter and 18” High with a QCC‐1 cylinder valve.
1. Turn the “Hand Wheel” on cylinder clockwise until it stops to ensure the Cylinder Valve is fully
closed.
2. Turn all of the burner knobs to the OFF position.
3. Connect the 3/8” Flare end of the hose to the 3/8” Flare end of the brass coupling on the unit using
a 3/4” open wrench.
Do not apply pipe sealant. (These are flared fittings). Note: remember the
rubber line on the hose and regulator must be protected from sharp edges, hot surfaces, aggressive
building materials that could cut, melt, or damage the line. A separate approved gas line might be
needed to go between the hose and regulator and the griddle to position the rubber line in a safe
location.
4. Connect the regulator to the LP cylinder. Only hand-tighten the regulator.
5. Check for leaks using a soapy water solution by spraying on all connections, including all of the
valves, fittings, lines etc. (any and all gas connections have the ability leak and therefore it is critical to
check for leaks before each use)
6. To disconnect after you have used the appliance, turn the burner knobs to the OFF position.
7. Close the Cylinder Valve by turning the Hand Wheel counter-clockwise until it stops.
8. Disconnect the regulator from the LP cylinder after use.