C-RF6.
Owner’s Record The model and warranty numbers are located on the rear of the unit. Record the warranty in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. Model No. CDC-RF6 Warranty Number FCC Warning The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules.
Table of Contents Before installing and operating this unit, please read this manual thoroughly and retain it for future reference. . Antes de instalar y operar esta unidad, por favor lea este manual detenidamente y guardelo para referencia en el futuro. English lndice Owners’s Record ................................................ .2 FCC Warning........................................................ 2 Features ............................................................... 4 Precautions ............
Features Congratulations on your purchase of your Blaupunkt CDC-RF6 FM Modulator CD Changer. This unit is designed to convert CD sound into FM signals (89.1 MHz or 88.7 MHz) and play them through any FM car stereo.
Before Installing and Testing (continued) Transport Lock Screws The mechanism in the CD changer is “locked” into place during shipment by three transport screws. Be sure to remove the screws prior to testing the system and installation. To keep dust out of the unit, which could cause a malfunction, place the enclosed seals over the screw holes after the Transport Lock Screws have been removed.
Electrical Connections Electrical Connections l Caution: before making connections, disconnect the ground wire terminal of the car battery to avoid short circuits. l Use this unit only with negative ground 12 Volt (1 l- 16 Volt) direct current (DC). l Be sure to use the supplied changer cord. Using a cord other than the one supplied may cause noise or damage. l Be sure to connect the changer cord to the FM Modulator before mounting.
Installation . Recommendations l l l l l l l l l l Carefully choose the mounting location so that the unit won’t interfere with normal driving. Avoid installing the unit in a place: - Subject to temperatures exceeding 55 degrees C (131 degrees F) (such as in a car parked in direct sunlight.
Horizontal Installation 0 l l l l l Confirm that Anti-Vibration Switches on both left and right sides are set to position H. Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8). Attach brackets (L) and (R) to their respective brackets (5) using tha hexagonal bolts (M6 x 20) and the hexagonal nuts (M6). where to attach the unit. Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing Affix the unit to the floor by pressing in place.
Vertical l l l 0 Installation . *,,,, Ant!-Vibration Cs.,&4..%. Confirm that Anti-Vibration Switches on both left and right sides are set to position V. Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6). Pull back the carpet and determine where to attach the unit.
45O Installation l l l Confirm that Anti-Vibration Switches on both left and right sides are set to position 45”. Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6). l l l l where to attach the unit. Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing. Affix the unit to the floor by pressing in place.
Suspended Installation 0 l l l Make sure that the unit does not hinder the movement of torsion bar spring or other parts of the trunk lid. Confirm Anti-Vibration Switches on both the left and right sides are set to position “HI’. Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8). . ~1111 Anti-Vibration Switches 11111) [--F&-l - 0 l Determine the mounting location and drill four mounting holes. Q l Attach the CD changer with the tapping screws (M5 x 12). . 3.
Installation of the FM Modulator Install the FM Modulator to the floor or other surface with the included tapping screws (M3x12).
Magazine & Compact DiscsNotes on the Disc Magazine Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. Here are some suggestions on how to take care of your discs and the magazine: l l l l l l l l Use compact discs that have the mark compact disc logo. @iF@ DIGITAL AUDIO Do not use 3” (8cm) discs with the CDC-RF6. Handle the disc by its edge, and to keep the disc clean, do not touch the surface.
Magazine & Compact Discs Installing The Magazine 1. Slide the door toward the right. 2. Position the magazine so the top is facing up, and the arrow is facing the changer. Push it in until it clicks into place. Note: When the magazine is used for the first time, it will not lock into place unless the power supply has been connected. Make sure the door is closed. Otherwise, foreign matter may enter the unit, and contaminate the lenses inside the changer.
Operating Instructions . Before operating the unit for the first time (or after reconnecting the battery, etc.) press the Reset Button on the Commander. See page 5. Load the discs into the CD magazine and install the magazine into the CD charger. Turning Unit On/Playing A CD Vehicle ignition must be on. Turn on the car stereo and select FM band. Tune the radio to either 89.1 or 88.7 MHz. (depending on frequency chosen during installation).
Operating Instructions l BLAUPUNKT .. . E. i.. L.3 . . I...3 . . I... 7 8 6 5 1 2 CDC-RF6 COMMANDER Mix Play Track Mix - Press the MIX Button (5). MIX appears in the Display, and the tracks on the disc now heard are played in a random order. When all the tracks have been played, they will be played again, this time in a different random order.
Troubleshootinq Guide . The following check will assist in the correction of most problems that you might encounter with your unit. Perform the checks described below before contacting your Blaupunkt dealer. Cause Symptom No Power Fuse blown. Remedy Replace with a fuse of the same type and rating as the original. If the fuse blows again, consult with your dealer. Improper connection. Check connections. No Sound Improper connection. Check connections.
Error Codes If the changer malfunctions, one of the following error codes will be displayed: Error Display Cause : : I: t==== I”‘: :.... I. : : :. . . . :. 3.... Disc change malfunction. Consult with dealer. Disc loaded with print facing up or disc is dirty. Load disc properly. Clean disc. Temperature inside car too hot. Allow the car to cool. Then press the Play/Pause Button. Magazine has not been installed. Install magazine. g.1.: :I..: :11.: : :-: El : :..1.: :...5 E...! No discs in magazine.
. BLAUPUNKT Bosch Group Robert Bosch Corporation Sales Group-Mobile Communications Division 2800 South 25th Avenue, Broadview, Illinois 60153 0 Robert Bosch Corporation Printed in Japan 1 RAGPlOA71600
