M I N I B I K E 2,6
SAFETY WARNING Always pay attention to the instructions and safety warnings below This manual contains important safety information and instructions which should be read carefully before operating the vehicle. For your own safety and the safety of others follow these rules. Neither manufacturer nor distributor is responsible for injuries caused by unsafe and improper use of the vehicle.
SERVICE MANUAL FOR USE AND MAINTENANCE OF MINIBIKE Before starting the operation of your Minibike, read thoroughly these directions. CONTENTS PAGE INTRODUCTION .............................................................................................................. 2 BASIC TECHNICAL DATA ...............................................................................................2 UNPACKING AND BASIC CONTROLS - FIG. 1 ............................................................3 SAFETY..............
INTRODUCTION Minibike 2,6 is intended for a drive on closed tracks with even, smooth, and dust-free surface. Both growns - up and children can ride on the Minibike. Children only under the supervision of a grown - up and responsible person. If the terms of a track are fulfilled, the Minibikes can be used for races. Minibike Blata should not be used during winter season and under bad weather conditions.
UNPACKING AND BASIC CONTROLS: The Minibike is packed and delivered with folded handlebars and levers mounted on them. After unpacking, set up the handlebars in such a function position that will suit you best. However at maximum handlebars turning, the brake levers must not bump into the lining. After setting - up the handlebars, tighten the nuts 1 on handlebars sleeves, the brake levers 2, and acceleration handle 3 acc. to Fig. 1.
STARTING THE ENGINE To be done only on the starting stand - Fig. 2. After opening the tank filling hole, fill the tank with fuel and close it by screwing - in cap.Open the petrol supply cock by turning the small lever into position “ON”, Fig.3. Set the choke lever into position “C” , Fig. 3. Without turning the accelerating handle, pull gently twice the starting wire and by next quick pull start the engine. It is not allowed to pull the starting wire up to full winding off.
RIDE After mounting the Minibike and slow turning the acceleration handle, you are starting your ride. Before braking, turn back the acceleration handle and depress slightly the front brake lever and then the rear brake lever. Beware of the wheels not to get them in skid. The Minibike engine will be switched off by pusching the red buttom of the stop switch on handlerods. After the first half- hour ride it is necessary to check the tightening of screws and nuts, especially of the engine.
6
345.100.00 345.100.00 347.010.
MINIBIKE - 2,6 200.000.00 110.001.00 110.001.01 110.002.00 110.004.00 110.004.01 110.004.02 110.004.03 110.005.00 110.006.00 110.006.01 110.006.02 110.006.03 110.008.00 110.011.00 110.015.00 110.017.00 110.019.00 110.020.00 110.021.00 110.022.00 110.023.00 110.024.00 110.028.00 110.031.00 110.032.00 110.053.00 110.055.00 110.056.00 110.057.00 110.059.00 110.060.00 110.063.00 110.065.00 110.067.00 110.068.00 110.069.00 110.069.01 110.069.02 110.069.03 110.070.00 110.072.00 110.073.00 110.074.00 110.075.
118.001.00 118.002.00 118.003.00 118.005.00 118.010.00 518.001.
916.072.02 916.072.02 916.072.02 916.072.
ADJUSTING THE BRAKES Small incremental brake adjustment : Free play at the handlebar lever is effected by turning the knurled end on the cable adjustor. This will allow the lever to be set at the nominal to ¼ inch of free lever movement. 3 4 Basic brake adjusting: Screw in the knurled cable adjustor at the brake lever so the cable is in it’s most slack starting position.. At the caliper, loosen the nut, No. 3 and tighten the adjustable bolt No. 4, so the wheel cannot turn. Back off bolt No.
DISMANTLING AND MOUNTING THE REAR WHEEL, FIG. 5 Unscrew the rear axle nut 920.011.01 and loosen the nuts 920.009.01 on chain tighteners. Shift the wheel forward and remove the chain. At pulling out the wheel axle, secure the rear wheel two distance rollers fall out. The wheel mounting to be carried out in reverse sequence. It is necessary to see to the right location of distance rollers. Use the shorter roller on the site of chain wheel and the longer one at the brake disc.
NON USE AND STORAGE PROCEDURE It is recommended to drain out all fuel from the tank and carburetor. Inflate the tires to the working pressure and put the minimotard on the stand. During a *long storage period, unbolt the spark plug and insert a couple of drops of the motor oil into the cylinder. Pull the starting rope a couple of times so a film of oil covers and evenly coats the cylinder walls and piston rings. * Long period is 90 days and longer.
