Powered Personal Transportation Electric Power Board Product Handbook FOR THE BLADEZ E-LITE 250 ELECTRIC POWER BOARD Model: PB-SM815 PLEASE BE SAFE WHEN RIDING . . .
IMPORTANT BATTERY MAINTENANCE and CHARGING INSTRUCTIONS: 1. You MUST Charge your scooter completely prior to initial use. (Follow charging instructions in your Product Handbook). 2. Charge immediately after every use. 3. Charge before storage. You must charge every 30 days if not in use. 4. Only use the charger provided. 5. DO NOT allow your unit to Deep Discharge. 6. For safety purposes, DO NOT charge for over 24 hours. 7. Turn the unit OFF when not in use.
IMPORTANT PLEASE READ THIS BEFORE USING THIS PRODUCT WARNING This product does not conform to Federal Motor Vehicle Standards and is not intended for operation on public streets, roads or highways. Serious injury can result from the unsafe operations of this product. Operator can minimize these risks by using certain safety equipment such as: safety helmet, goggles, gloves, elbow and kneepads and appropriate footwear.
DO NOT TAKE YOUR BLADEZ POWERBOARD BACK TO THE STORE! CONTACT US FIRST IF YOU HAVE ANY QUESTIONS OR NEED ASSISTANCE, PLEASE CALL BLADEZ, TOLL FREE AT: (866) EBLADEZ (866) 325-2339 MONDAY thru FRIDAY, 8am to 5pm PST or visit us on the web at: www.ebladez.
TABLE OF CONTENTS BATTERY MAINTENANCE AND CHARGING INSTRUCTIONS:………………………………………………………………...2 GETTING TO KNOW YOUR BLADEZ POWER BOARD…………………………………. 6 BOX CONTENTS………………………………………………………………………………. 7 GETTING STARTED…………………………………………………………………………... 7 FOLDING AND STORAGE…………………………………………………………………..10 CHARGING SYSTEM…………………………………………………………………………10 RECOMMENDED TOOLS…………………………………………………………………… 11 BRAKING SYSTEM………………………………………………………………………….. 11 TIRES AND WHEELS………………………………………………………………………...
GETTING TO KNOW YOUR BLADEZ POWER BOARD Before operating your Bladez E-Lite 250 ELECTRIC POWERBOARD, please familiarize yourself with the following features: 1. 2. 3. 4. 5. 6. Accelerator Lever Brake Lever Quick Release Deck Kick Stand 250W DC Motor Mud Guard 7. Rear Drum Brake 8. 1.1AH Charger 9. Folding Handle 10. Control Panel (with multi-function LED) 11.
BOX CONTENTS Your Bladez E-LITE should come complete with: 1. 2. 3. 4. Bladez E-Lite 250 ELECTRIC POWERBOARD AC Wall Charger Allen Wrench Instruction Manual and Registration Card GETTING STARTED YOUR SCOOTER WILL COME CHARGED OUT OF THE BOX BUT YOU MUST CHARGE YOUR E-LITE 250 FOR 6-8 HOURS EVEN IF THE LIGHT IS GREEN PRIOR TO FIRST USE! Before you Ride 1. The E-Lite is shipped with the Handlebars unattached. 2. You need to insert the accelerator and brake levers into the handlebars.
* Note: It is not advisable to operate your Power Board on low tire pressure. This will negatively affect speed, handling and performance. Quick Release Deck The E-LITE is equipped with a quick release deck to make it easier to get to the batteries and the pc board. To release the deck locate the two levers towards the front of the deck. (FIG. 3). Pull up on the levers to release the deck then slide it forward as you pull up on it to remove it.
*It is recommended on initial charge to charge for 6-8 hours even if the light is GREEN. Unfolding 3. To unfold your E-Lite, hold the unit with one hand, while gently pulling up on the handlebars with the other. 4. Fully extend the handlebars to their upright position until you feel the mechanism lock into place. 5. You are now ready to ride your Power Board! Riding 6. Makes sure that all of the bolts and screws are tightened. 7. Raise the kickstand to its upright position. 8.
FOLDING AND STORAGE 13. To fold your Power Board. Using one hand, gently pull up on the Folding Handle, while lowering the handlebars with the other (Fig. 7A). 14. Lock the unit into the folded position by rotating the locking hook over the folded handlebars (Fig. 7B). When you are done riding the E-Lite you can fold it down for compact storage, carrying and transportation. To fold down the E-Lite, use one hand to pull up on the FOLDING HANDLE, while using the other to gently pull down on the handlebars.
Multi-Function LED The E-LITE 250 comes equipped with a multi function LED which will let you know the status of your batteries while riding. When the scooter is turned on and the batteries are fully charged the LED light on the scooter will be green, indicating a full charge. Once the battery voltage drops between 21V to 23V the LED will have a green and red light on at the same time. Indicating you have about 60% of your battery power left.
To Inflate the Tires 1. Remove the valve stem cover and expose the valve stem (Fig. 8). 2. Using a standard bicycle pump, inflate the tires to 50 PSI and replace the valve stem cover. The Bladez E-Lite uses an identical rim and tires assembly on the front and rear wheels, which means that the tires can be rotated. The wheels are actually two wheel halves (split rim) bolted together to make it easier to remove and replace the tire. Empty all air from the tire, prior to loosing the bolts to split the rim.
For regular adjustments: 1. Using a 16mm wrench, loosen the axel bolts on each side of the rear wheel (Fig. 9). 2. While the axel bolts are loose, using a 10mm wrench loosen the tension bolts behind the rear wheel of the ELite and move the rear wheel backwards to remove the slack from the chain (fig. 10). 3.
OTHER QUESTIONS Where can get replacement and aftermarket parts? From your local Servicing Dealer of over the web at: www.ebladez.com For additional questions, service instruction, further information and important phone numbers, please go to the Bladez website at www.ebladez.com.
Page 15
www.ebladez.com Bladez, Corp.
Page 17
