BLH02550 Blade Scimitar LRX FPV BNF Manual

7
EN
Band
CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
FS/IRC 5740 5760 5780 5800 5820 5840 5860 5880
Band E 5705 5685 5665 5665 5885 5905 5905 5905
Band A 5865 5845 5825 5805 5785 5765 5745 5725
Race Band 5658 5695 5732 5769 5806 5843 5880 5917
Band B 5733 5752 5771 5790 5809 5828 5847 5866
Using the Video Transmitter
Preparing the Scimitar LRX Quadcopter for Flight
1.Beforeeachight,ALWAYSpoweronthetransmitterbeforeconnectingtheightbatterytothequadcopter.Aftereach
ight,disconnecttheightbatteryfromthequadcopterbeforepoweringoffthetransmitter.
NOTICE: Connectingtheightbatterybeforepoweringonthetransmittercanstartthebindingprocess.Pleaseseethe
Transmitter and Receiver Bindingsectionofthismanualformoreinformation.
2.WhentheESCbeeps,theightcontrollerisinitializedandreadyforight.
Theightcontrollerwillnotarmthemotorsuntilthethrottlestickisinthelowestpossibleposition.
Available Frequencies, North America (mHz)
TheVT1000videotransmitterincludesanSMAAntenna
AdaptorwhichconnectstothemainPCBwithanMMXC
connector.
Installacompatible5.8GHzantennaontotheSMAconnector.
IMPORTANT: Donotkinkorcuttheantennaadaptoror
antennawires.Antennawiresarecoaxialwires,there-
forekinksorcutswilldegradeperformance.
NOTICE:Poweringonthevideotransmitterwithout
anantennaconnectedwillcausedamagetothevideo
transmitter.Damagefrompoweringonthevideo
transmitterwithoutacompatibleantennaattachedis
notcoveredunderwarranty.
Connecting an Antenna
ConsultlocallawsandordinancesbeforeoperatingFPV
equipment.Insomeareas,FPVoperationmaybelimitedor
prohibited.Youareresponsibleforoperatingthisproductin
alegalandresponsiblemanner.
SeetheAvailable Frequenciestabletondthedesiredvideo
channelandband.Thevideotransmitterchannelandband
arechangedusingthebuttonsonthetopofthequadcopter,
asshown.TherearetworowsofLEDsvisiblethroughtheLED
window.TherowofredLEDsindicatesthechannelselected
(1–8).TherowofblueLEDsindicatestheselectedband(A,B,
E,F,R).ThegreenLEDsindicatethevideotransmitteroutput
powerlevelselected.
OnlychangethevideochannelandbandwhenthevideotransmitterisnottransmittingasignalorisinPitMode.Ifanyofthe
greenLEDsareglowingsolid,seethedirectionsbelowtostoptransmittingavideosignalpriortochangingthechannelor
band.
Channel and Band Selection
1. AshortpressofbuttonBwillchangechannels.Quicklypressandreleasethebuttononceforeachchanneluntilthe
desiredchannelisreached.
2. AlongpressofbuttonBwillchangetheband.PressandholdbuttonBforseveralsecondsandreleaseforeachband
change.
Power Level Selection
1. PressandholdbuttonAtochangethepoweroutput.AllgreenLEDsoffmeansRFisoff,oneashinggreenLEDisPitMode,one
solidgreenLEDis25mW,twosolidgreenLEDsis200mW,threesolidgreenLEDsis600mW.
Tip: Useascrewdrivertoaccessthevideotransmitterbuttons,ifyouarenotusingtheremotesensorfeatureonthetransmitter.
A
B
E
F
R
1
2
3
4
5
6
7
8
Channels
Button A
Button B
Power
Levels
Bands*