RTF Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Introduction As you are about to see, the Blade® mCP X truly is an ultra micro heli experience unlike any other. Its advanced flybarless design reduces drag on the rotorhead and significantly boosts cyclic control response. This, combined with its exceptionally lightweight airframe, delivers a level of power and responsiveness that eclipses that of any ultra micro heli you may have flown before.
Battery Warnings and Guidelines The Battery Charger (EFLC1006) included with the Blade mCP X has been designed to safely charge the Li-Po battery. CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fire, personal injury, and/or property damage. • By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries. • If at any time the battery begins to balloon or swell, discontinue use immediately.
Battery Charging Celectra™ 1-Cell 3.7V Variable Rate DC Li-Po Charger Instructions 1. C onnect the power supply to an appropriate power source. 2. Insert the output plug from the power supply into the power input slot of the Variable Rate Charger. 3. Select the appropriate charge current for your battery by pushing the + or -, which are the smaller buttons to the right and left of the Start (middle) button, (When charging your 200mAh battery, set the charger to 0.7 amps). 4.
® Programming Your Transmitter (Computer Transmitters Only) Program your transmitter before attempting to bind or fly the helicopter. If the throttle and pitch programming values are incorrect, the helicopter will not respond. Transmitter programming values are shown below for the Spektrum DX6i, DX7 and DX8. The Spektrum DX8 model file is also available for download online at the Spektrum DX8 Community.
® Transmitter and Receiver Binding If you purchased an RTF model, the transmitter is bound to the model at the factory. To bind or re-bind your mCP X to your chosen transmitter, please follow the directions below: Binding is the process of programming the receiver of the control unit to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ or JR® DSM® technology equipped aircraft transmitter to the receiver for proper operation.
Understanding the Primary Flight Controls If you are not familiar with the controls of your mCP X, take a few minutes to familiarize yourself with them before attempting your first flight.
Throttle Hold Throttle hold is used to turn off the helicopter motors if the helicopter is out of control, in danger of crashing or both. Activate throttle hold anytime the helicopter is in danger to reduce the chance of damaging the helicopter in a crash. Throttle hold will stop the motor in normal or stunt mode. Throttle Hold ON (DX4e) Press the trainer button anytime to turn throttle hold ON after connecting the battery to the helicopter. The blue LED flashes, indicating throttle hold is ON.
Installing the Flight Battery 1. Lower the throttle and throttle trim to the lowest settings. 2. Power on the transmitter. 3. Install the flight battery in the battery holder. Connect the battery cable to the 3-in-1 control unit. NOTICE: Do not allow the helicopter to move until the blue LED on the 3-in-1 control unit is solid. NOTICE: Always disconnect the Li-Po battery from the 3-in-1 control unit of the aircraft when not flying. Failure to do so will render the battery unusable.
Troubleshooting Guide Problem Possible Cause Solution Throttle at high position Reset controls with throttle stick and throttle trim at center or lowest setting Switches not in normal position Set flight mode to OFF/0 and exit throttle hold. Pitch or throttle servo reversing improperly configured Reset servo reversing Refer to “Programming your Transmitter” Throttle hold on Turn off HOLD with throttle low and trim centered or low.
Exploded View and Parts Listings L K M J G C I H (PITC) E A N F R P D A Part # Description BLH3601 Flybarless 3-in-1 Control Unit, Receiver/ESCs/Gyros: mCPX/2 Part # Description I BLH3509 Complete Precision Swashplate: mCP X J BLH3510 High-performance Main Rotor Blade Set with Hardware: mCP X BLH3511 Fast Flight Main Rotor Blade Set with Hardware: mCP X (not shown) B BLH3602 Tail Boom Assembly with Tail Motor/ Rotor/Mount: mCPX/2 C BLH3503 Main Motor with Pinion: mCP X D BLH35
Main Board Plug Configuration Elevator Aileron Main Motor Pitch S Tail Motor O B U (ELEV) Q V (AILE) Optional Parts T Part # Description P BLH3518 Complete Red Canopy with Vertical Fin: mCP X Q BLH3520R Red Vertical Fin with Decal: mCP X R BLH3521 EFLH3021 Canopy Mounting Grommets (8): BMCX2/T, MSR, FHX, MH-35, mCP X S BLH3522 Rotor Head Linkage Set (8): mCP X BLH3523 Hardware Set: mCP X (not shown) EFLB 2001S30 200mAh 1S 3.
Limited Warranty What this Warranty Covers Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase by the Purchaser.
Warranty and Service Contact Information Country of Purchase Horizon Hobby Address 4105 Fieldstone Rd Horizon Service Center Champaign, Illinois (Electronics and engines) 61822 USA United States of America 4105 Fieldstone Rd Horizon Product Support Champaign, Illinois (All other products) 61822 USA Units 1-4 Ployters Rd Staple Tye United Kingdom Horizon Hobby Limited Harlow, Essex CM18 7NS United Kingdom Hamburger Str.
FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2011081402 Product(s): Blade mCP X 2 BNF Item Number(s): Equipment class: BLH3680EU, BLH3680UK 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE Directive 1999/5/EC and EMC Directive 2004/108/EC: EN 301 489-1 V1.7.1: 2006 EN 301 489-17 V1.3.
©2011 Horizon Hobby, Inc Blade, E-flite, Celectra, Bind-N-Fly, DSM, JR and ModelMatch are trademarks or registered trademarks of Horizon Hobby, Inc The Spektrum trademark is used with permission of Bachmann Industries, Inc. US 7,391,320, D578,146. US 7,898,130. PRC patent number ZL 200720069025.2. Other patents pending.
