Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Table of Contents First Flight Preparation ..................................................... 4 Flying Checklist ............................................................... 4 Parts of the Quadcopter ................................................... 4 Assembly ......................................................................... 5 Transmitter Setup ............................................................ 6 Installing the Flight Battery ..............................................
First Flight Preparation Flying Checklist • Remove and inspect contents • Begin charging the flight battery • Assemble the aircraft • Program your computer transmitter • Install the flight battery in the aircraft (once it has been fully charged) • Bind your transmitter • Familiarize yourself with the controls • Find a suitable area for flying ❏ Always turn the transmitter on first ❏ Plug the flight battery into the lead from the ESC ❏ Allow the ESC to initialize and arm properly ❏ Fly the model ❏ Land the mod
Assembly Assemble and Install the Optional Camera Mount If you wish to use an additional camera to record your flights, follow the directions below to assemble and install the optional video camera mount. 1. Assemble the camera mount as shown (A). Do not fully tighten the screws. Use removable thread locking compound to keep the screws from loosening due to vibration. 2. Remove the 8 screws holding the top plate to the quadcopter (B). 3. Carefully lift the top plate away from the frame. 4.
Transmitter Setup DX6, DX7 (Gen 2), DX8 (Gen 2), DX9, DX18, DX20 SETUP LIST FUNCTION LIST Model Type Airplane F-Mode Setup Switch 1 Switch 2 Inhibit Inhibit Channel Assign Channel Input Config 1 Throttle 2 Aileron 3 Elevator 4 Rudder 5 Gear Switch B 6 Aux 1 Switch H Servo Setup Chan Travel THR 150/150 AIL 148/148 ELE 148/148 D/R & Expo Switch (B) Chan Pos 0 AILE 1 2 0 ELEV 1 2 Reverse Normal Reverse Normal D/R 100/100 100/100 100/100 100/100 100/100 100/100 Chan RUD GER AUX1 Expo 0 0 0 0 0 0 Travel 1
Transmitter and Receiver Binding To bind or re-bind your quadcopter to your chosen transmitter, follow the directions below. Binding Procedure 1. Select the correct model in your transmitter. 2. Power off your transmitter. 3. Lower the throttle fully. 4. With the transmitter off, power on the quadcopter. The receiver will attempt to connect to the last transmitter it was bound to. The receiver LED will rapidly flash orange indicating the receiver has entered Bind Mode. 5.
Elevator Left Side View Elevator down Left Side View Elevator up Forward Backward Aileron Rear View Aileron left Rear View Aileron right Left Right Using the Video Transmitter NOTICE: Never power on the video transmitter without the antenna installed. Powering on without the antenna will damage the video transmitter. The video transmitter is located under the top plate of the quadcopter, with access holes to allow changing the band and channel, as shown in the illustration.
Adjusting the FPV Camera Angle To adjust the FPV camera angle: 1. Loosen the FPV camera angle adjustment screw on both sides of the quadcopter. DO NOT remove the screws. 2. Rotate the camera up or down to the desired angle. 3. Tighten the angle adjustment screws. DO NOT overtighten the screws. Angle Adjustment Screw Installing An Optional Video Camera To install an optional video camera: 1. Place the camera (not included) into the camera mount. 2.
Preparing the Conspiracy Quadcopter for Flight 1. Before each flight, ALWAYS power on the transmitter before connecting the flight battery to the quadcopter. After each flight, disconnect the flight battery from the quadcopter before powering off the transmitter. NOTICE: Connecting the flight battery before powering on the transmitter can start the binding process. Please see the Transmitter and Receiver Binding section of this manual for more information. 2.
Troubleshooting Guide Problem Possible Cause Quadcopter not initialized on a level Quadcopter control response is surface inconsistent or requires extra trim to neutralize movement Battery not correctly placed Motor arm switch is in the OFF position Throttle too high and/or throttle trim is too high Quadcopter will not respond to throttle Quadcopter moved during initialization Throttle channel is reversed Quadcopter does not function and smells burnt after connecting the flight battery Quadcopter has re
Parts Explosion 5 13 16 15 10 9 14 18 11 17 6 7 8 1 5 11 4 3 4 5 2 3 12 4 Parts Listings 1 2 3 4 5 6 7 8 9 10 Part # Description BLHA1002 BLHA1003 BLHA1006 BLHA1021 BLH02001 BLH02002GR BLH02002RE BLH02002YE BLH02003 BLH02004 5x4 FPV Race Prop, 2Blade, Green 5x4 FPV Race Prop, 3Blade, Green 20A ESC BLHeli Opto Quad Pack 2205-2350Kv FPV Racing Motor Main Frame Frame Skirt, Green Frame Skirt, Red Frame Skirt, Yellow LED Board HD Camera Mount Part # Description 11 BLH02005 12 BLH02006 Hardw
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
Warranty and Service Contact Information Country of Purchase Horizon Hobby Contact Information Horizon Service Center servicecenter.horizonhobby.com/ (Repairs and Repair Requests) RequestForm/ productsupport@horizonhobby.com Horizon Product Support United States (Product Technical Assistance) 877-504-0233 of America websales@horizonhobby.com Sales 800-338-4639 sales@horizonhobby.co.
©2016 Horizon Hobby, LLC. Blade,Conspiracy, SAFE, the SAFE logo, DSM, DSM2, DSMX, the BNF logo, ModelMatch, EC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks or logos are property of their respective owners.
