® RTF READY-TO-FLY
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Length Height Blade Nano QX 3D Specifications 1.00 oz (27 g) 5.12 in (130mm) Flying Weight 1.65 in (42mm) To register your product online,visit www.bladehelis.com Blade Nano QX 3D Components Airframe – Blade Nano QX 3D Motors – 6mm Brushed On-board Electronics – 4 -in-1 mixer/ESCs/Gyro Battery – 200mAh 1S 3.
NOTICE: Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured. 1. Insert the charger into a USB port. The charger only uses power from the USB port, it will not connect to your computer. USB power supplies, such as those used to charge cellular phones, can also be used. 2. Connect the charger connector to the battery as shown and the battery will begin charging. 3.
RTF Transmitter and Receiver Binding Your RTF transmitter comes prebound to the model. If you need to re-bind, follow the directions below. IMPORTANT: Set up your transmitter before binding your transmitter to the aircraft. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a specific transmitter. You need to ‘bind’ your chosen Spektrum™ or DSM2 ®/DSMX ® technology equipped aircraft transmitter to the receiver for proper operation.
RTF Transmitter Controls Flight mode switch Trigger (bind switch) A Dual rate switch Bind switch H G B C F D SAFE Technology Flight Modes – RTF RTF The Nano QX 3D RTF model comes with the Blade MLP6DSM transmitter. This transmitter has a switch that lets the pilot change among 3 SAFE Technology flight modes. IMPORTANT: Ensure the flight mode switch is in the desired position before flying. • Beginner Mode (switch position 0).
Transmitter Setup Table Transmitter IMPORTANT: Set up your transmitter before binding your transmitter to the aircraft. Non-Computerized Transmitter Setup (DX4e and DX5e) Before binding a non-computerized transmitter, ensure all servo reversing is set to normal and trim is at center. Computerized Transmitter Setup Start all transmitter programming with a blank ACRO model (do a model reset), then name the model. Set Dual Rates to: HIGH 100% LOW 70%.
Understanding the Primary Flight Controls Flying the Nano QX 3D If you are not familiar with the controls of your Nano QX 3D, take a few minutes to familiarize yourself with them before attempting your first flight. Takeoff Left Side View Throttle (left stick) Descend Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model flies as desired.
Exploded View Parts Listings 5 6 4 1 2 3 4 5 6 Part # Description BLH7102 BLH7105 BLH7106 EFLB2001S30 BLH7103 BLH7104 EFLH1063 BLH7101 EFLC1013 Brushed Motors (4): Nano QX 3D Props (4): Nano QX 3D Main Frame: Nano QX 3D 200mAh 1S 3.7V 30C LiPo Battery Upper Canopy: Nano QX 3D Frame Support: Nano QX 3D MLP6DSM SAFE Transmitter 4-in-1 Control Unit: Nano QX 3D 1S USB Li-Po Charger, 500mAh High Current UMX Connector: Nano QX 3D 3 Optional Parts 2 Part # Description EFLC1006 Celectra 1S 3.
Troubleshooting Guide Problem Nano QX 3D control response is inconsistent or requires extra trim to neutralize movement Nano QX 3D will not respond to throttle Nano QX 3D does not function and smells burnt after connecting the flight battery Nano QX 3D has reduced flight time or is underpowered EN Possible Cause Aircraft not initialized on a level surface Solution Disconnect the flight battery, center the control trim and re-initialize the quadcopter Battery not correctly placed in battery slot Adju
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
Warranty and Service Contact Information Country of Purchase United States of America United Kingdom Germany France Horizon Hobby Contact Information Horizon Service Center servicecenter.horizonhobby. (Repairs and Repair Requests) com/RequestForm/ www.quickbase.com/db/ Horizon Product Support bghj7ey8c?a=GenNewRecord (Product Technical Assistance) 888-959-2304 sales@horizonhobby.com Sales 888-959-2304 sales@horizonhobby.co.
©2015 Horizon Hobby, LLC. Blade, E-flite, SAFE, the SAFE logo, DSM, DSM2, DSMX, Bind-N-Fly, the BNF logo, Celectra, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks or logos are property of their respective owners. Patents pending.
