S3 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di istruzioni RTF
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby. com or www.towerhobbies.com and click on the support or resources tab for this product.
Table of Contents USB Charging Warnings............................... 4 Battery Charging.......................................... 4 Transmitter Setup Table (BNF)...................... 5 Transmitter Control (RTF)............................. 5 Installing the Flight Battery.......................... 6 Transmitter and Receiver Binding................. 7 Control Tests................................................ 7 Understanding the Primary Flight Controls �� 8 Flight Modes..................................
USB Charging Warnings The Battery Charger (EFLC1008) included with your helicopter has been designed to safely charge the Li-Po battery. • Always monitor the charging area and have a fire extinguisher available at all times. • Always end the charging process if the battery becomes hot to the touch or starts to change form (swell) during the charge process. • Always connect the positive leads (+) and negative leads (–) correctly.
Transmitter Setup Table (BNF) DX series, NX series, IX series SYSTEM SETUP FUNCTION LIST Model Type HELI Servo Setup Travel Reverse Swash Type Normal Chan THR 100/100 Normal F-Mode Setup AIL 100/100 Normal Switch 1 Switch B ELE 100/100 Normal Throttle Cut -130%1 D/R & Expo Channel Assign Chan Sw (F) Pos D/R Expo Channel Input 0 100/100 0 1 Throttle Throttle AILE 1 100/100 0 2 Aileron Aileron 0 100/100 0 ELEV 3 Elevator Elevator 1 100/100 0 4 Rudder Rudder 0 100/100 0 RUDD 5 Gear Switch B 1 100/100 0 6 AU
Dual Rate Selection (RTF transmitter) The control sensitivity can be changed by pressing and releasing the right control stick. The LED on the transmitter will show solid for high sensitivity (default) and flashing for low sensitivity. RTF Transmitter LED Indicator The transmitter LED gives a visual representation for various data. The following table gives an explanation of the possible LED indications.
Transmitter and Receiver Binding Binding is the process of programming the receiver of the control unit to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2 ®/ DSMX ® technology equipped aircraft transmitter to the receiver for proper operation. If you purchased an RTF model, the transmitter is bound to the model at the factory.
Aileron Rear View Rear View Aileron left Aileron right Collective Pitch Left Side View Left Side View Collective pitch up Collective pitch down Understanding the Primary Flight Controls If you are not familiar with the controls of your Nano S3, take a few minutes to familiarize yourself with them before attempting your first flight.
Aileron Rear View Rear View Left Right Aileron left Aileron right Flight Modes The Nano S3 RTF comes with the Blade MLP6DSM transmitter. This transmitter has a flight mode switch that lets the pilot change among the following flight modes. • The model will NOT return to a level attitude position when you release the controls. • The helicopter has no bank angle limit. • Both the cyclic and yaw controls are at fast, aerobatic rate.
Panic Recovery If you get into distress while flying in any mode, push and hold the Bind/Panic Switch and move the control sticks to their neutral position. SAFE technology will immediately return the aircraft to an upright level attitude, if the aircraft is at a sufficient height with no obstacles in its path. Return the collective stick to 50% and release the Panic Switch to turn off Panic Recovery and return to the current flight mode.
Low Voltage Cutoff (LVC) Landing LVC decreases the power to the motors when the battery voltage gets low. When the motor power decreases and the red LED on the ESC flashes, land the aircraft immediately and recharge the flight battery. LVC does not prevent the battery from overdischarge during storage. To land, slowly decrease the throttle while in a low-level hover. After landing, disconnect and remove the battery from the aircraft after use to prevent trickle discharge.
Problem Possible Cause Solution Power off transmitter, move transmitter a larger distance from Transmitter is too near aircraft aircraft, disconnect and reconnect during binding process flight battery to aircraft and follow LED on receiver binding instructions flashes rapidly and Bind switch or button was not aircraft will not bind to Power off transmitter and repeat held while transmitter was transmitter bind process powered on (during binding) Aircraft or transmitter is too Move aircraft and transmitte
Exploded View and Parts Listings 15 17 15 18 18 17 16 17 17 12 20 2 5 14 13 19 12 6 3 19 5 1 11 7 10 13 EN
9 8 4 21 22 Description Flight Control: Nano S3 nCP S Main motor Nano S2 Main plastic frame Nano S2 Tail Fin DSV40LBC-35 Servo *1 DSV40LBC-50 Servo *1 Nano S2 Canopy Nano CP X Tail Boom and Motor Tail Rotor Landing Skid & Battery mount Main Gear Carbon Fiber Main Shaft with Collar 12 BLH3307 & Hardware 13 BLH3308 Servo Pushrod set with Ball Links 14 BLH3309 Complete Precision Swashplate 15 BLH1305 Main Rotor Blade Set: Nano S2 16 BLH3312 Main Rotor Hub with Hardware Feathering Spindle with O-rings and 1
Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. NOTICE: Do not ship Li-Po batteries to Horizon.
FCC Information RTF BLH01301 includes Nano S3 helicopter and MLP6 transmitter BLH01350 Helicopter - Contains FCC ID: BRWWACO1T SPMRMLP6 Transmitter - Contains FCC ID: BRWWACO1T BNF Basic (BLH01350) includes Nano S3 Helicopter FCC ID: BRWWACO1T Supplier’s Declaration of Conformity Blade Nano S3 RTF/BNF (BLH01301/BLH01350) This device complies with part 15 communications. However, there is of the FCC Rules.
Compliance Information for the European Union EU Compliance Statement: Blade Nano S3 RTF/BNF (BLH01301/BLH01350); Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive - Amending 2011/65/ EU Annex II 2015/863. The full text of the EU declaration of conformity is available at the following internet address: https://www. horizonhobby.com/content/supportrender-compliance.
©2021 Horizon Hobby, LLC. Blade, the Blade logo, E-flite, the BNF logo, DSM, DSM2, DSMX, Safe, the SAFE logo, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks and logos are property of their respective owners. US 9,930,567. US 10,419,970.
