User Manual

Einrichten des Senders
Sie müssen Ihren Sender zuerst programmieren, bevor Sie den Helikopter binden oder fl iegen können. Die Werte, die Sie zum Programmieren Ihres Senders für
Spektrum DX6i, DX6, DX7/DX7se, DX7s, DX8, DX9 und DX18 Empfänger benötigen, sind unten angeführt. Die Spektrum-Modelldateien für AirWare Sender stehen auch
online in der Spektrum Community zum Download zur Verfügung.
DX7/DX7se
DX6i
SETUP LIST
SETUP LIST
ADJUST LIST (PROGRAMMIEREINSTELLUNGEN)
ADJUST LIST (PROGRAMMIEREINSTELLUNGEN)
ADJUST LIST (PROGRAMMIEREINSTELLUNGEN)
Model Type Reverse/Umkehr Swash Type / Taumelscheibe Timer
HELI
THRO N
1 Servo 90 Degree
Type: Down
Time: 4:00
Switch: Trainer
AILE N
ELEV N
RUDD R
GYRO N
PITC R
Model Type Reverse/Umkehr Swash Type / Taumelscheibe Timer
HELI
THRO N
1 Servo 90 Degree
Type: Down
Time: 4:00
Switch: Trainer
AILE N
ELEV N
RUDD R
GYRO N
PITC N
Dual Rate / Expo
Switch Pos. D/R Expo
AILE
0 100% INH
1 85% INH
ELEV
0 100% INH
1 85% INH
RUDD
0 100% INH
1 85% INH
Dual Rate / Expo
Switch Pos. D/R Expo
AILE
0 100% INH
1 85% INH
ELEV
0 100% INH
1 85% INH
RUDD
0 100% INH
1 85% INH
Travel Adjust /
Weg
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GYRO 100%
PITC 100%
Travel Adjust /
Weg
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GYRO 100%
PITC 100%
Sub-Trim*
THRO 0
AILE 0*
ELEV 0*
RUDD 0*
GYRO 0
PITC 0
Sub-Trim*
THRO 0
AILE 0*
ELEV 0*
RUDD 0*
GYRO 0
PITC 0
Gyro
Pos. Rate SW-F. Mode
0 77.0% NORM 0
1 77.0% STUNT 0
Gyro
Pos. Rate SW-F. Mode
0 77.0% NORM 0
1 77.0% STUNT 0
Throttle Curve / Gas Kurve
L234H
NORM 0% 30% 60% 60% 60%
STUNT 75% 75% 75% 75% 75%
HOLD 10% 10% 10% 10% 10%
Throttle Curve / Gas Kurve
L234H
NORM 0% 30% 60% 60% 60%
STUNT 1 100% 100% 100% 100% 100%
HOLD 10% 10% 10% 10% 10%
Pitch Curve / Pitch Kurve
L234H
NORM 30% 40% 50% 75% 100%
STUNT 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100%
Pitch Curve / Pitch Kurve
L234H
NORM 30% 40% 50% 75% 100%
STUNT 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100%
SWASH MIX /
Taumelscheibenmischer
INHIBIT
SWASH MIX /
Taumelscheibenmischer
INHIBIT
* Nehmen Sie beim AR7200BX niemals Sub-Trimmungen oder Trimmungen für AILE, ELEV oder RUDD vor.
DX6/DX7s/DX8/DX9/DX18
SETUP LIST
Model Type Reverse/Umkehr Swash Type / Taumelscheibe Timer
HELI
THRO N
1 Servo 90 Degree
Type: Down
Time: 4:00
Switch: Trainer
AILE N
ELEV N
RUDD R
GYRO N
PITC N
Dual Rate / Expo
Switch Pos. D/R Expo
AILE
0 100% INH
1 85% INH
ELEV
0 100% INH
1 85% INH
RUDD
0 100% INH
1 85% INH
Travel Adjust /
Weg
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GYRO 100%
PITC 100%
Sub-Trim*
THRO 0
AILE 0*
ELEV 0*
RUDD 0*
GYRO 0
PITC 0
Gyro
Pos. Rate SW-F. Mode
0 54.0% NORM 0
1 54.0% STUNT 0
Throttle Curve
L234H
NORM 0% 30% 60% 60% 60%
STUNT 1 75% 75% 75% 75% 75%
STUNT 2 100% 100% 100% 100% 100%
HOLD 10% 10% 10% 10% 10%
Pitch Curve
L234H
NORM 30% 40% 50% 75% 100%
STUNT 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100%
Swash Mix
INHIBIT
Lieferumfang:
• Blade 450 X
• 3S 11.1V 2200mAh 30C Li-Po Akku
• DC LiPo Balancer Ladegerät
®
®
Airframe
Blade 450 X
Motor
440H Brushless Aussenläufer 4200Kv
Empfänger
Spektrum AR7200BX with BeastX
Technology
ESC
35A Brushless Regler
Taumelscheibenservos
Digitales Taumelscheibenservo
12 g Metallgetiriebe
Heckservo
Digitales Heckrotorservo
12 g Metallgetriebe
Akku
3S 11.1V 2200mAh 30C Li-Po
Ladegerät
DC Li-Po Balancier Ladegerät
Komponenten
BLH4380A
Sie können Ihr Produkt online unter www.bladehelis.com registrieren.