User Manual

6
EN
Throttle Hold
Installing the Flight Battery
Binding Procedure
1. ProgramyourtransmitterusingtheTransmitterSetupfoundinthismanual.
2. InsertthebindplugintheBND/DATportonthereceiver.
3. ConnecttheightbatterytotheESC.TheorangeLEDontheAR636willbeginashingrapidlytoindicatebindmode.
4. Movethethrottlesticktothelowthrottlepositioninnormalmode.
5. FollowtheproceduresofyourspecictransmittertoenterBindMode.Thesystemwillconnectwithinafewseconds.Onceconnected,theorangeLEDwillturnoff
andtheAR636Awillstarttheinitializationprocess.
6. Whentheinitializationprocessiscomplete,theStatusLEDlightwillcomeonsolidorange.
7. DisconnecttheightbatteryandremovethebindplugfromtheAR636A.Storethebindpluginaconvenientplace.
1. Lowerthethrottle.
2. Poweronthetransmitter.
3. Centerthethrottletrim.
4. ToallowtheESCtoarmandtokeeprotorsfrominitiatingatstartup,turnon
throttleholdandnormalightmodebeforeconnectingtheightbattery.
5. Attachhookmaterialtothehelicopterframeandloopmaterialtothebattery.
6. Installtheightbatteryonthehelicopterframe.Securetheightbatterywitha
hookandloopstrap.ConnectthebatterycabletotheESC.
7. DonotmovethehelicopteruntiltheAR636Ainitializes.Theswashplatewill
center,indicatingthattheunitisready.TheAR636Awillalsoemitasolid
orangeStatusLEDwhenitisready.
8. Thehelicoptermotorwillemit2ascendingtones,indicatingtheESCisarmed.
CAUTION:AlwaysdisconnecttheLi-PobatteryfromtheESCpowerlead
whennotyingtoavoidover-dischargingthebattery.Batteriesdischargedto
avoltagelowerthanthelowestapprovedvoltagemaybecomedamaged,resultingin
lossofperformanceandpotentialrewhenbatteriesarecharged.
Transmitter and Receiver Binding
BindingistheprocessofprogrammingthereceivertorecognizetheGUID(Globally
UniqueIdentier)codeofasinglespecictransmitter.Youneedto‘bind’your
chosenSpektrum™DSM2/DSMXtechnologyequippedaircrafttransmittertothe
receiverforproperoperation.
WARNING: YoumustmovethethrottletotheLOW/OFFpositionduring
binding.Failuretodosomaycausetherotorbladestospinandthe
helicoptertoliftduringtheAR636Ainitialization,whichcouldresultin
damagetopropertyandinjury.
NOTICE: Removethebindplugtopreventthesystemfromenteringbindmode
thenexttimethepoweristurnedon.
CAUTION:WhenusingaFutaba
®
transmitterwithaSpektrum™DSM2
®

module,youmustreversethethrottlechannel
Ifyouencounterproblems,obeybindinginstructionsandrefertotransmitter
troubleshootingguideforotherinstructions.Ifneeded,contacttheappropriate
HorizonProductSupportofce.
Throttleholdonlyturnsoffthemotoronanelectrichelicopter.Youmaintainpitch
anddirectioncontrol.
ThebladeswillspinifthrottleholdisOFF.Forsafety,turnthrottleholdONanytime
youneedtotouchthehelicopterorcheckthedirectioncontrols.
Throttleholdisalsousedtoturnoffthemotorifthehelicopterisoutofcontrol,in
dangerofcrashing,orboth.