User Manual

11
EN
EN
Servo Adjustment
TheBlade360CFX3Sissetupatthefactoryandtestown.Theservoadjustment
stepsareusuallyonlynecessaryinspecialcircumstances,suchasafteracrashor
ifaservoorlinkageisreplaced.
WARNING:Toensureyoursafety,alwaysdisconnectthemotorwiresfromthe
ESCbeforeperformingthefollowingsteps.Afteryouhavecompletedtheadjust-
ments,reconnectthemotorwirestotheESCbeforeattemptingtoythemodel.
Entering Servo Adjustment Mode
DX6G2, DX6e and DX6i Users:
1. Lowerthethrottlesticktothelowestposition.
2. PowerONthetransmitter.
3. Installtheightbatteryonthehelicopterframe,securingitwiththehookand
loopstrap.
4. ConnectthebatteryconnectortotheESC.
5. Beforeinitializationiscomplete,hold
theleftsticktothebottomleftcorner
andtherightsticktothebottomright
cornerasshown.
6. Whentheswashplateservosmove,
youhaveenteredServoAdjustment
Mode.
7. ReleasethesticksandproceedtoAdjustingtheServoNeutralPositiontomake
anydesiredchanges.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1. Lowerthethrottlesticktothelowestposition.
2. PowerONthetransmitter.
3. Installtheightbatteryonthehelicopterframe,securingitwiththehookand
loopstrap.
4. ConnectthebatteryconnectortotheESC.
5. Placethehelicopteronaatsurfaceandleaveitstilluntiltheorangereceiver
LEDglowssolid,indicatinginitializationiscomplete.
6. Holdtheleftsticktothebottomleftcornerandtherightsticktothebottom
rightcornerasshown.
7. Holdthebind/panicswitchuntilthe
swashservosmove.
8. Releasethesticksandthebind/panic
switch.ThemodelisnowinServo
AdjustmentMode.
9. ProceedtoAdjustingtheServoNeutralPositiontomakeanydesiredchanges.
Adjusting the Servo Neutral Position
WiththemodelinServoAdjustmentMode,thecontrolstickandgyroinputsare
disabledandtheservosareheldintheneutralposition.Checkthepositionofthe
servoarmstoseeiftheyareperpendiculartotheservos.
• Ifthearmsareperpendiculartotheservos,noadjustmentisnecessary.
ExitServoAdjustmentMode.
• Ifoneormoreservoarmisnotperpendiculartotheservos,continuetheservo
adjustmentprocess.
Whilewatchingtheswashplateservos,applyforwardcyclicandrelease.Oneof
theservoswilljump,indicatingwhichservoisselected.Pressforwardcyclicand
releaseuntiltheservothatneedstobeadjustedisselected.
Oncetheservoyouwishtoadjustisselected,movethecyclicsticklefttorightto
adjusttheservoneutralpositioninthedesireddirection.
Ifyouwouldliketoresetthecurrentservotothedefaultneutralposition,holdthe
rudderstickfullrightfor1second.
Therangeofadjustmentislimited.Ifyouareunabletoadjusttheservoarmtobe
perpendiculartotheservo,youmustresettheservotothedefaultneutralposition,
removetheservoarmandplaceitbackontotheservoasclosetoperpendicular
aspossible.Youmaythenadjusttheservoneutralpositionusingtheleft/right
cyclicstick.
Swashplate Leveling
Beforesavingyouradjustmentsandexitingservoadjustmentmode,verifythe
swashplateislevelandbothmainrotorbladesareat0degrees.
Iftheyarenot,makelinkageadjustmentsasnecessary.
Saving the Servo Adjustments
DX6, DX6e, and DX6i Users:
1. Lowerthethrottlesticktothelowestpositionandreleasethesticks.
2. Movethetailrotorsticktotheleftandholduntiltheservosmove.
3. Releasethetailrotorsticktosavetheservoadjustments.
4. ReconnectthemaindrivemotortotheESC.Yourmodelisnowreadyforight.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1.Lowerthethrottlesticktothelowestpositionandreleasethesticks.
2.PressandholdswitchIuntiltheswashservosmove.
3.ReleaseswitchItosavetheservoadjustments.
4.ReconnectthemaindrivemotortotheESC.Yourmodelisnowreadyforight.
Allofthesettingsarestoredinternally,soyouradjustmentswillbemaintained
eachtimeyouinitializethemodel.