User Manual

10
EN
EN
Entering Gain Adjustment Mode
DX6G2, DX6e and DX6i Users:
1. Lowerthethrottlesticktothelowestposition.
2. PowerONthetransmitter.
3. Installtheightbatteryonthehelicopterframe,securingitwiththehookand
loopstrap.
4. ConnectthebatteryconnectortotheESC.
5. Beforeinitializationiscomplete,move
andholdbothtransmitterstickstothe
bottomrightcornerasshown.
6. Whentheservosmove,youhave
enteredGainAdjustmentMode.
7. ReleasethesticksandproceedtoAdjustingtheGainValuestomakeany
desiredchanges.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1. Lowerthethrottlesticktothelowestposition.
2. PowerONthetransmitter.
3. Installtheightbatteryonthehelicopterframe,
securingitwiththehookandloopstrap.
4. ConnectthebatteryconnectortotheESC.
5. Placethehelicopteronaatsurfaceandleaveitstilluntiltheorangereceiver
LEDglowssolid,indicatinginitializationiscomplete.
6. Moveandholdbothtransmittersticks
tothebottomrightcornerasshown.
7. Pressandholdthebind/panicswitch
untiltheswashservosmove.
8. Releasethesticksandthebind/panic
switch.Themodelisnowin
GainAdjustmentMode.
9. ProceedtoAdjustingtheGainValuestomakeanydesiredchanges.
Adjusting the Gain Values
IfyouareusingaSpektrum™telemetry-enabledtransmitter,thegain
adjustmentscanbeviewedontheFlightLogscreen.Refertoyourtransmitter
instructionstolocatethisscreen.Thegainparametercurrentlyselectedwillash
onthetransmitterscreen.IfyouarenotusingaSpektrumtelemetry-enabled
transmitter,theparameterandgainvaluesareindicatedbythepositionofthe
swashplateonthehelicopter.
Parameter # Display location Swash Position Page #
1 A 100%totheLeft 1
2 B 50%totheLeft 1
3 L 25%totheLeft 1
4 R SwashplateLevel 1
5 A 25%totheRight 2
6 B 50%totheRight 2
7 L 100%totheRight 2
Pagenumber
1=Cyclicgains
2=Tailrotorgains
Gainparameter
selected
Gainvalue
displaylocation
Flight Log Screen
Swash Position Gain Value
Fullbackward 0%
50%backward 50%
Levelforwardandbackward 100%
50%forward 150%
Fullforward 200%
OnceyouhaveenteredGainAdjustmentMode,youcanmovethecyclicstick
forwardandbacktoselectthegainparameteryouwouldliketoadjust.Movingthe
stickaftwillselectthenextparameter.Movingthestickwillselecttheprevious
parameter.
TheselectedgainparameterisindicatedontheFlightLogscreenandbythelean
oftheswashplateontherollaxis.
Thecurrentgainvalueforthe
selectedparameterisindicatedon
theFlightLogscreenandbythe
angleoftheswashplate(forwardor
backward)asshowninthetableat
theright.
Movethecyclicsticklefttorightto
adjustthegainvalue.Movingthe
stickrightwillincreasethegainvalue.Movingthestickleftwilldecreasethegain
value.
Itisalwaysbesttoadjustonegainatatime.Makesmalladjustments(5%orless)
andtestythemodeltoevaluatetheadjustmentsthatweremade.
Ifyouwouldliketoresetthecurrentgainvaluetothedefaultvalueof100%,move
andholdtherudderstickfullrightfor1second.Theswashwilllevelonthepitch
axis,indicatinga100%gainsetting.
Saving the Gain Adjustments
DX6, DX6e and DX6i Users:
1. Lowerthethrottlesticktothelowestpositionandreleasethesticks.
2. Movethetailrotorsticktotheleftandholduntiltheservosmove.
3. Releasethetailrotorsticktosavethegainadjustments.
4. ReconnectthemaindrivemotortotheESC.Yourmodelisnowreadyforight.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users:
1. Lowerthethrottlesticktothelowestpositionandreleasethesticks.
2. PressandholdswitchIuntiltheswashservosmove.
3. ReleaseswitchItosavethegainadjustments.
4. ReconnectthemaindrivemotortotheESC.Yourmodelisnowreadyforight.