User Manual

Transmitter Setup and Binding
Transmitter Model Type Switch Select Reversing Throttle Cut Model Setup Switch Position
DX6i
acro n/a gear - R
All others - N
act
Travel Adj: Flap ↑ 120 ↓ 100
Throttle Subtrim: ↑ 10
Fl aps: FLAP
Norm ↑ 100
land ↓ 100
Mi x 1:
gear → gear act
rate: D –60%, U 0%
SW: ele d/r
Smart Mode = F Mode ( POS. 0)
Return Home = F Mode (POS. 1)
AP MODE = ELE D/R (POS 1)
GIMBAL control = FLAP (POS 1), Throttle controls gimbal angle
Ac celerometer calibration = Set FLAP to POS 0 and cycle Flight Mode switch 4 times
Co mpass calibration = Set FLAP to POS 1 and cycle Flight Mode switch 4 times
DX6
airplane Ch annel Assign:
Channel Input Cong
(2nd page):
Gear: B
AUX1: A
S ervo setup:
AUX1 - R
All others - N
Th rottle cut:
Position: –130%
Switch: Switch i
Se rvo setup:
Travel:
120%
140%
AX1
Smart Mode = Switch B ( POS. 0)
AP MODE = Switch B (POS 1)
Return Home = Switch B (POS. 2)
GIMBAL Control = Switch A (POS 1), Throttle controls gimbal angle
Co mpass calibration = Switch A (POS 0) and cycle B switch 4 times
Ac celerometer calibration = Switch A (POS 1) and cycle B switch 4 times
DX7s
airplane Knob: AUX2
Gear: AUX1
Flap: Gear
Se rvo setup:
All NORM
Th rottle cut:
0% Trainer
Se rvo setup:
Travel:
Aux1 120% 140%
Smart Mode = Flap switch ( POS. 0)
AP MODE = FLap switch (POS 1)
Return Home = Flap switch (POS. 2)
GIMBAL Control = Gear switch (POS 0), Knob controls gimbal angle
Co mpass calibration = Gear switch (POS 0) and cycle FLAP switch 4 times
Ac celerometer calibration = Gear switch (POS 1) and cycle FLAP switch 4 times
DX8
airplane Gear: AUX1
Knob: AUX2
F Mode: Gear
Se rvo setup:
All NORM
Th rottle cut:
0% Trainer
Se rvo setup:
Travel:
Aux1 120% 140%
Smart Mode = F Mode switch ( POS. 0)
AP MODE = F Mode switch (POS 1)
Return Home = F Mode switch (POS. 2)
GIMBAL Control = Gear switch (POS 0), Knob controls gimbal angle
Co mpass calibration = Gear switch (POS 0) and cycle FLAP switch 4 times
Ac celerometer calibration = Gear switch (POS 1) and cycle FLAP switch 4 times
DX9/DX18
airplane Ch annel Assign:
Channel Input
Co ng (2nd page):
Gear: B
AUX1: A
AUX2: R Knob
Se rvo setup:
All NORM
Th rottle cut:
Position: –130%
Switch: Switch i
Se rvo setup:
Tr avel:
140%
120%
AX1
Smart Mode = Switch B ( POS. 0)
AP MODE = Switch B (POS 1)
Return Home = Switch B (POS. 2)
GIMBAL Control = A switch (POS 0), Knob controls gimbal angle
Co mpass calibration = A switch (POS 0) and cycle B switch 4 times
Ac celerometer calibration = A switch (POS 1) and cycle B switch 4 times
Binding the 350 QX3 To Your Transmitter
1. With the transmitter and quadcopter powered OFF, connect the battery to the 350 QX3.
2. Place the 350 QX3 on a at level surface.
3. Power the 350 QX3 ON and let it initialize. The status LED will remain off.
4. Hold the 350 QX3 upside down until the status LED ashes blue, indicating it has entered bind mode.
5. Set the quadcopter back upright.
6. On your transmitter, ensure the throttle is in the low position and the throttle trim is at neutral.
7. Power ON your transmitter in bind mode according to the instructions included with your transmitter.
8. When the binding process is successful, the 350 QX3 will emit a quick, 3-beep tone and the LED will ash either green, purple or red, depending on which ight mode is
selected. If the LED is ashing red, the 350 QX3 is in Return Home mode. Switch to Smart or AP Mode (green or purple ashing) before attempting to start the motors.
9. Place the quadcopter outdoors in the desired starting position in preparation for ight.
EN