User Manual

6
EN
Transmitter Model
Type
Reverse
Setup
Throttle
Cut
Setup
Mode Setup Switch Positions Throttle Cut Return Home Dual Rate
Switch
High
Rate
Low
Rate
DX4e (New)*
w/3-position
switch
N/A N/A N/A N/A
Position 0 = SMART Mode
Lower throttle
trim until motors
stop turning
Press and Hold
TRAINER/BIND
Release to EXIT
Rate
100%
fi xed
70%
fi xed
Position 1 = Stability Mode
Position 2 = Agility Mode
DX5e (New)*
w/3-position
switch
N/A N/A N/A N/A
Position 0 = SMART Mode
Lower throttle
trim until motors
stop turning
Press and Hold
TRAINER/BIND
Release to EXIT
Rate
100%
fi xed
70%
fi xed
Position 1 = Stability Mode
Position 2 = Agility Mode
DX6i Acro
THRO-N
ELEV-N
GEAR-R
AILE-N
RUDD-N
FLAP-N
ACT
Travel Adj: GEAR POS (0) GEAR: ↑100%;
GEAR/F MODE POS (1) GEAR: ↓40%
FLAPS: Norm ←↑100; LAND ↓100
MIX 1: ACT; GEAR → GEAR ACT
RATE D 0%; U + 100%
SW MIX TRIM INH
SUB TRIM THRO ↑ 15-20%
GEAR 0; Mix 0 = SMART Mode
Press throttle cut
FLAP Position 0
= OFF
FLAP Position 2 =
Return Home
ELEV-AIL D/R 100% 70%
GEAR 1; Mix 0 = Stability Mode
GEAR 1; Mix 1 = Agility Mode
DX7/7SE Acro
FLAP-R (6)
Others-N
N/A
Travel Adj: GEAR (0)↑100%;
GEAR (1) ↓40%
MIX 1: FLAP → Gear OFF/ON
RATE → -50%
0%
SW: MIX OFFSET: 0
GEAR (0);
Mix (0) = SMART Mode
Lower throttle
trim until motors
stop turning
FLAP Pos 0
= OFF
FLAP Pos 1
= Return Home
ELEV-AIL D/R 100% 70%
GEAR (1);
Mix (0) = Stability Mode
GEAR (1);
Mix (1) = Agility Mode
DX7S Acro
AUX1-R
Others-N
Set To:
Trainer
Switch Select:
Move Gear to F MODE (F MODE:GEAR)
Leave FLAPS as AUX1
Set All Others to INH
MIX 1: GER > GER
RATE: 0%
-100%
OFFSET: 0%; TRIM: INH; SW: Mix0
F MODE (0) = SMART Mode
Press
Trainer
FLAP Pos 0 = OFF
FLAP Pos 2 =
Return Home
ELEV-AIL D/R 100% 70%F MODE (1) = Stability Mode
F MODE (1);
HOLD (1) = Agility Mode
DX8 Acro
AUX1-R
Others-N
Set To:
Trainer
Switch Select: F-Mode to Gear;
Flap to Aux 1
All Others to INH
F MODE (0) = SMART Mode
Press Trainer/
Bind
FLAP Pos 0
= OFF
FLAP Pos 2
= Return Home
ELEV-AIL D/R 100% 70%F MODE (1) = Stability Mode
F MODE (2) = Agility Mode
DX9/DX18 Acro
AUX1-R
Others-N
Set To:
I (BIND)
Channel Assign: NEXT
1-4: N/A 5 Gear: B
6 AUX1: D 7 AUX2: I
8-10: INH
B (0) = SMART Mode
Press I (BIND)
D (FLAP) Pos 0
= OFF
D (FLAP) Pos 2 =
Return Home
ELEV-AIL D/R 100% 70%B (1) = Stability Mode
B (2) = Agility Mode
* Old versions of the DX4e and DX5e (with 2-position channel 5 switches) are not recommended for the 350 QX. Only Smart Mode and Agility Mode will be
available with GPS On.
Transmitter Setup (BNF)
CAUTION: When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module
manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.