Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni ® ® ®
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Table of Contents AR7200BX Default Blade 300 CFX Setup......................................................... 9 AR7200BX Parameter Menu Tips .................................................................... 9 AR7200BX Fine-tuning and Adjustment......................................................... 10 Blade 300 CFX Troubleshooting Guide ........................................................... 10 Limited Warranty ......................................................................................
Low Voltage Cutoff (LVC) Once the battery reaches 9V under load, the ESC will continuously lower power supplied to the motor until complete shutdown occurs. This helps prevent over-discharge of the Li-Po battery. Land immediately once the ESC activates LVC. Continuing to fly after LVC can damage the battery, cause a crash or both. Crash damage and batteries damaged due to over-discharge are not covered under warranty. Repeatedly flying the helicopter until LVC activates will damage the helicopter battery.
Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Binding Procedure 1. Program your transmitter using the Transmitter Setup found in this manual. 2. Insert the bind plug in the BND/DAT port on the receiver. 3. Connect the flight battery to the ESC.
Control Tests CAUTION: You must complete the Rudder and Cyclic tests prior to flight. Failure to complete the tests and ensure the sensor directions are not reversed can cause the helicopter to crash, resulting in property damage and injury. Rudder 1. Power on the transmitter. 2. Turn TH HOLD ON and put the transmitter into normal mode. 5. Release the rudder control. Manually turn the helicopter nose to the left. The tail rotor blades automatically move as shown.
Motor Control Test Place the helicopter outdoors on a clean, flat and level surface (concrete or asphalt) free of obstructions. Always stay clear of moving rotor blades. 1. The motor beeps twice when the helicopter’s ESC arms properly. Before you continue, confirm that TH HOLD is ON. 3. Ensure the throttle is lowered completely. Turn throttle hold off at this time and confirm the transmitter is still set to normal flight mode. Slowly increase the throttle until the blades begin to spin.
Blade Helicopter Belt Tension Belt tension that is too tight results in loss of power and causes the belt to wear more quickly. Tension that is too loose can cause belt damage and loss of tail rotor control in flight. To check for proper belt tension: To adjust belt tension: 1. View the tail rotor drive belt through the opening at the back of the main frame. 2. Use a hex wrench or standard screwdriver to compress the belt through the opening. 3.
AR7200BX Default Blade 300 CFX Setup Firmware version 3103.0.
AR7200BX Fine-tuning and Adjustment Observed Behavior Suggested Adjustment Cyclic response is too slow or too fast Adjust dual rates to fit your flying style.
Limited Warranty assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Warranty and Service Contact Information Country of Purchase Horizon Hobby Contact Information Horizon Service Center servicecenter.horizonhobby.com/RequestForm/ (Repairs and Repair Requests) www.quickbase.com/db/ Horizon Product Support United States of America (Product Technical Assistance) bghj7ey8c?a=GenNewRecord 888-959-2304 sales@horizonhobby.com Sales 888-959-2304 sales@horizonhobby.co.
29 14 15 16 14 14 12 12 18 14 13 17 9 8 20 20 19 18 17 29 16 14 9 13 12 14 12 14 16 14 15 Exploded View / Explosionszeichnung / Vue éclatée / Vista esplosa 46
47 30 42 55 33 44 45 32 43 32 45 46 45 36 43 45 30 32 35 41 44 32 31 38 42 37 40 32 39 37 40 39 35
48 11 1 7 51 52 53 54 4 52 5 23 24 24 23 22 2 25 27 2 21 26 6 26 54 3 54 10 3 58 1 50 47
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio # Part # English 1 BLH4601 2 BLH4602 3 BLH4603 Main Frame: 300 CFX Bearing Blocks: 300 CFX Bottom Plate Mount: 300 CFX Deutsch Français Blade 300 CFX: Hauptrahmen 300 CFX - Flancs du châssis Blade 300 CFX: Lagerblöcke 300 CFX - Paliers Blade 300 CFX: Halter Lagerplatte unten 300 CFX - Fixations de train 300 CFX - Fixations de poutre de 4 BLH4604 Tail Boom Mount: 300 CFX Blade 300 CFX: Halter Lagerplatte unten queue 5 BLH4605 Gyro
# Part # 36 BLH4531 37 BLH4532 38 BLH4533 39 BLH4534 40 BLH4535 41 BLH4536 English Horizontal Stabilier/Fin Mount: 300 CFX Tail Case: 300 CFX Tail Rotor Pitch Lever Set: 300 CFX Bearings 3x7x3 (2): 300 CFX Tail Rotor Shaft and Drive Pulley (2): 300 CFX Tail Rotor Pitch Control Slider Set: 300 CFX Deutsch Français Italiano Heckrotorgehäuse:300 CFX Umlenkhebel f.
Part # English Deutsch Français BLH4542A BLH4542B BLH4542C 300X -Support de servo d’anticouple en aluminium 300X -Support de stabilisateur en aluminium 300X -Carter d’anticouple en aluAluminum Tail Case Set: 300 CFX Aluminium Heckrotorgehäuse: 300X minium 300X -Levier de pas d’anticouple en Aluminum Tail Rotor Pitch Lever Aluminium Heckrotorgestänge 300X aluminium Set: 300 CFX 300X -Axe d’anticouple avec poulie en Tail Rotor Shaft Aluminum Drive Heckrotorwelle mit Antriebsrad: 300X aluminium Pulley: 30
©2015 Horizon Hobby, LLC. Blade, DSM, DSM2, DSMX, Dynamite, Prophet, E-flite, Celectra, the BNF logo, ModelMatch, AirWare and EC3 are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. BeastX is a registered trademark of Markus Schaack and is used with permission. The Spektrum AR7200BX employs technology exclusively licensed to Horizon Hobby, LLC from freakware GmbH. Created 2/15 43357.
