Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Table of Contents First Flight Preparation .....................................................4 Flying Checklist ...............................................................4 Charging Warnings...........................................................4 Battery Charging..............................................................5 Installing the Flight Battery ..............................................5 Transmitter and Receiver Binding.....................................6 SAFE Technology .........
First Flight Preparation Flying Checklist • Remove and inspect contents • Begin charging the flight battery • Install the flight battery in the quadcopter (once it has been fully charged) • Program your computer transmitter • Bind your transmitter • Familiarize yourself with the controls • Find a suitable area for flying ❏ Always turn the transmitter on first ❏ Plug the flight battery into the lead from the 4-in-1 control unit ❏ Allow the 4-in-1 control unit to initialize and arm properly ❏ Fly the model ❏ La
Battery Charging NOTICE: Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured. 1. Connect the AC power supply to the charger. B 2. Connect the other end of the power supply to an appropriate AC power source. A 3. Connect the battery balance lead to the charger adapter (A). 4. Connect the charger adapter to the charger (B). 5. Press the Start/Stop Button to begin charging. 6.
Transmitter and Receiver Binding To bind or re-bind your quadcopter to your chosen transmitter, please follow the directions below. General Binding Procedure 1. Disconnect the flight battery from the quadcopter. 2. Select a clean model memory on your transmitter (computer radios only). 3. Select Acro or Airplane model type on your transmitter. 4. Make sure all servo reversing is set correctly for your radio. Refer to the Transmitter Setup Table. 5. Center all trims on your transmitter. 6.
N/A N/A DX5e (Old) w/ 2 Position N/A Switch N/A MLP6DSM N/A N/A N/A MLP4DSM Reverse Setup DX4e (Old) w/ 2 Position N/A Switch Model Type Transmitter N/A N/A N/A N/A Mode Setup Channel 5 (1) = Agility Mode Channel 5 (0) = Stability Mode, Low Angle ACT/AUX (ON) = Agility Mode ACT/AUX (OFF) = Stability Mode, Low Angle Channel 5 (2) = Agility Mode Channel 5 (1) = Stability Mode, High Angle Channel 5 (0) = Stability Mode, Low Angle Press Right Stick = Agility Mode (Quad Solid Red LED)
EN 8 Acro Acro DX6i DX7/7SE N/A N/A Mode Setup Travel Adj: GEAR (0)↑ 100%; GEAR (1) ↑40% MIX 1: FLAP → Gear OFF/ON FLAP - R (6) RATE → -50% All Others - N 0% SW: MIX OFFSET: 0 Setup List: Throttle Cut – ACT Travel Adj: GEAR (0)↑ 100%; F MODE (1) ↓40% GEAR - R FLAPS: Norm ←↑100; LAND ↓100 All Others - N MIX 1: ACT; Gear → Gear ACT RATE D 0% U + 100% SW MIX TRIM INH N/A DX5e (New) w/ 3 Position N/A Switch Reverse Setup N/A Model Type DX4e (New) w/ 3 Position N/A Switch Transmitter 100% 70% F
EN Acro Acro DX9/DX18 Acro DX7S DX8 Model Type Transmitter Mode Setup Channel Assign: NEXT 1-4: N/A 5 Gear: B AUX1 - R 6 AUX1: I All Others - N 7-10: Inh Throttle Cut: Switch H Switch Select: Trainer to Aux 1 F Mode to Gear AUX1 - R All Others - N All Others to Inh Throttle Cut: MIX 1 Switch Select: Trainer to Aux 1; F Mode to Gear Set All Others to Inh Throttle Cut: MIX 1 AUX1 - R Mixing: All Others - N MIX 1: GER > GER RATE: 0% -100% OFFSET: 0%; TRIM: Inh SW: Ele D/R Reverse Setup Camera
LED Codes Equipment LED Color Blue Green Red Quadcopter All LEDs White LED Status Rapid Blink Solid Solid Solid Slow Blink Medium Blink Rapid Blink Blink Operation Bind Mode Stability Mode high angle Stability Mode low angle Agility Mode 7.1V Low Voltage Warning 7.0V Low Voltage Warning 6.9V Low Voltage Warning 6.
Flying the 200 QX Takeoff When you are prepared to fly, move both sticks into the bottom inside corners, then back to center. Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model flies as desired. Once the trim is adjusted, begin flying the model. Typical flight times for the included battery range from 5 to 7 minutes. Low Voltage Cutoff (LVC) LVC decreases the power to the motors when the battery voltage gets low.
Troubleshooting Guide Problem Quadcopter control response is inconsistent or requires extra trim to neutralize movement Quadcopter will not respond to throttle Quadcopter does not function and smells burnt after connecting the flight battery Quadcopter has reduced flight time or is underpowered LED on receiver flashes rapidly and aircraft will not respond to transmitter (during binding) LED on the receiver flashes rapidly and the quadcopter will not respond to the transmitter (after binding) Crashes immed
Exploded View 7 8 10 9 5 1 6 2 4 13 10 6 5 12 2 Parts Listings Part # Description 1 2 3 4 BLH7701 BLH7702 BLH7703 BLH7704 5 BLH7705 6 BLH7706 7 8 BLH7707 BLH7708 Main Control Board: 200 QX Landing Gear: 200 QX Red LEDs: 200 QX Green LEDs: 200 QX Brushless Motor CW Rotation, 3000 Kv: 200 QX Brushless Motor CCW Rotation, 3000 Kv: 200 QX Gray Propellers: 200 QX Red Propellers: 200 QX 9 10 11 12 13 Part # Description BLH7709 BLH7710 BLH7711 BLH7712 EFLB8002SJ 4-in-1 ESC: 200 QX Body Set:
Limited Warranty questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Warranty and Service Contact Information Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby. com/RequestForm/ www.quickbase.com/db/ bghj7ey8c?a=GenNewRecord 888-959-2304 sales@horizonhobby.com 888-959-2304 sales@horizonhobby.co.
©2014 Horizon Hobby, LLC. Blade, E-flite, SAFE, the SAFE logo, DSM, DSM2, DSMX, the BNF logo, ModelMatch, Celectra and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks or logos are property of their respective owners. Patents pending. Created 5/14 43513.
