User manual

ManualsBrandsBlack ManualsSecurity CamerasBLK-CCD223VS

High Performance

Indoor/Outdoor Color CCTV

Dome Camera User Manual

Products: BLK-CCD203VS, BLK-CCD205VH, BLK-CPD206VH,

BLK-CCD223VS, BLK-CCD225VH, BLK-CPD226VH

Please read this manual before using your camera, and always follow the instructions

for safety and proper use. Save this manual for future reference.

BLK-DomeCameras_CM

3/18/11

Summary of content (24 pages)

PAGE 1
High Performance Indoor/Outdoor Color CCTV Dome Camera User Manual Products: BLK-CCD203VS, BLK-CCD205VH, BLK-CPD206VH, BLK-CCD223VS, BLK-CCD225VH, BLK-CPD226VH Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference.
PAGE 2
! WARNING  CAUTION Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. To prevent electric shock and risk of fire hazards: Use a power source that is within specification only. Do NOT expose this appliance to rain or moisture. REGULATORY NOTICE This device complies with Part 15 of the FCC Rules.
PAGE 3
TABLE OF CONTENTS Table of Contents SECTION 1 SECTION 2 SECTION 3 SECTION 4 APPENDIX A APPENDIX B Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
PRECAUTIONS Precautions Do not install the camera in extreme temperature conditions. Use the camera in environments where temperature is between 14°F and 122°F. Ensure adequate ventilation. Do not install or use the camera in an environment where the humidity is high. It can degrade the image quality. Do not install the camera under unstable lighting conditions. Severe lighting changes or flicker can cause the camera to work improperly. Never use the camera close to a gas or oil leak.
PAGE 5
SECTION 1: INTRODUCTION SECTION 1 Introduction DIGIOP Black high performance indoor/outdoor CCTV dome cameras feature a very high resolution Sony® CCD sensor providing 600 TVL, with a 2.8 – 11 mm lens, a digital wide dynamic range, dual voltage range support (24 VAC, 12 VDC), and on-screen display (OSD) for control and setup. These cameras are available with or without an IR array, and in either a durable plastic or vandalproof enclosure.
PAGE 6
SECTION 1: INTRODUCTION Lens IR Array Focus Lever Joystick / OSD Control Zoom Lever Video Out Tilt/Pan Bracket Internal Components - Cameras With IR 1.1 Cameras with a vandalproof enclosure Vandalproof cameras are IP67 rated and include a rugged die-cast aluminum enclosure. They are flush surface mountable using the mount adaptor box supplied. 1.1.
PAGE 7
SECTION 1: INTRODUCTION What’s in the box Optional dome bracket for wall and ceiling mounting 1.1.2 What you need To install the camera you will need: • • 12 VDC or 24 VAC power source Tools for mounting the camera 1.2 Cameras with a plastic enclosure 1.2.
PAGE 8
SECTION 1: INTRODUCTION • • • • Mounting screws (4) L-wrench User manual Dome bracket (optional) What’s in the box Optional dome bracket 4 www.digiop.
PAGE 9
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines • Outdoor installations: Use the rubber rings included with the machine screws (4) to ensure that the unit is sealed properly. • Dome/window care: Handle the dome carefully to prevent scratching. If a scratch appears over the lens, adjust the dome window to move the scratch out of view.  CAUTION Keep dome cover and camera lens clean.
PAGE 10
SECTION 2: INSTALLATION Power Connector 2.1.1 What you need To install the camera you will need: • • 12 VDC or 24 VAC power source Tools for mounting the camera 2.2 Vandalproof camera mounting The camera can be installed on a junction box or directly to a wall or ceiling. 1. Attach the surface mount bracket to the ceiling or wall using four (4) mounting screws. 2. Connect the dome base to the surface mount bracket using the screws with rubber rings provided. 3.
PAGE 11
SECTION 2: INSTALLATION 2.3 Plastic camera mounting 1. Connect the dome base to the mounting surface using four (4) screws. 2. Route the power and video cables to the camera location and attach them to the camera drop cable (see General guidelines above). 2.4 Camera adjustments 1. Attach a video setup monitor to the yellow RCA (EXTRA VIDEO OUT) connector inside the camera assembly, or setup a remote monitor for viewing video from the camera. 2. Power on the camera and video monitor. 3.
PAGE 12
SECTION 2: INSTALLATION Ceiling mounting Wall mounting 4. Adjust the image with the focus and zoom levers. 5. Configure your camera using the software menus in the OSD. See Software Setup in the following section of this manual. 6. Place the dome cover over the base and adjust the dome window. Tighten the captive screws that secure the cover to the base. 7. Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
PAGE 13
SECTION 3: SOFTWARE SETUP SECTION 3 Software Setup Use the SETUP joy stick on the OSD control panel to navigate through the menu system. Press the joy stick down (toward the PC board) to enter the SETUP menu or select an entry, rock the stick up or down to highlight an item in the list, and left or right display the option you want to select. The SETUP menu consists of a list of sub-menus or displays the option selected for a camera function. When sub-menus are available, the  symbol is shown. 3.
PAGE 14
SECTION 3: SOFTWARE SETUP DWDR: The DWDR feature employs intelligent light level control to compensate for strong backlight conditions. DWDR: OFF / ON DWDR OFF DWDR ON 3.3 WHITE BALANCE WHITE BAL: You can select one of the following modes: ATW1 / ATW2 / AWC g SET / MANUAL (INDOOR / OUTDOOR / MANUAL) —— —— —— —— —— —— —— —— 10 ATW1: Automatically adjusts color according to the available lighting for temperature range: 2500°K to 9500°K.
PAGE 15
SECTION 3: SOFTWARE SETUP 3.
PAGE 16
SECTION 3: SOFTWARE SETUP 3.5 DAY&NIGHT DAY&NIGHT: Select AUTO / COLOR / B/W / EXT · AUTO: Day&Night Auto mode —— —— —— —— D -> N LEVEL: 182 ~ 192 steps D -> N DELAY: 1 ~ 30 SEC N -> D LEVEL: 0 ~ 10 steps N -> D DELAY: 1 ~ 30 SEC COLOR: Day&Night only color mode B/W: Day&Night black and white (B/W) mode —— —— BURST: OFF / ON IR SMART: OFF / ON. This option controls the IR LED output level to compensate for object distance. The IR SMART option is used for objects in an area of the image.
PAGE 17
SECTION 3: SOFTWARE SETUP R GAIN: 0 ~ 255 HEIGHT: 0 ~ 15 WIDTH: 0 ~ 15 LEFT/RIGHT: 0 ~ 15 TOP/BOTTOM: 0 ~ 15 —— IR LEVEL: HIGH / LOW EXT: Day&Night EXT mode 3.6 DPC (Dead Pixel Compensation) Select DPC for dead pixel compensation processing. DPC can be set to OFF (default) or AUTO. When AUTO is used, the camera will remove defective pixels from an image automatically. 3.7 SPECIAL CAM TITLE: Select camera title menu (Text edit).
PAGE 18
SECTION 3: SOFTWARE SETUP MOTION: Select camera title menu (Text edit) —— —— —— —— —— —— —— —— AREA SEL: Select AREA1, AREA2, AREA3, AREA4 AREA STATE: Select OFF / ON HEIGHT: Select 0 ~ 15 steps WIDTH: Select 0 ~ 15 steps LEFT/RIGHT: Select 0 ~ 15 steps TOP/BOTTOM: Select 0 ~ 15 steps DEGREE: Select 0 ~ 255 steps VIEW: OFF / ON PRIVACY: You can cover an area of the screen.
PAGE 19
SECTION 3: SOFTWARE SETUP —— T: You can adjust the parking line thickness. (0 ~ 15 steps) IMAGE ADJ.: You can adjust camera image. —— —— —— LENS SHAD: LEVEL: 0 ~ 255 steps 2DNR: (on-screen Digital Noise Reduction) (OFF/ON) MIRROR: (reverse the camera image horizontally) (OFF/ON) MIRROR OFF —— —— —— —— MIRROR ON FONT COLOR: FONT: 16 colors (O ~ 15 steps) ID & TITLE: O ~ 15 steps CONTRAST: You can adjust contrast on screen. (0 ~ 255 steps) SHARPNESS: You can adjust camera image for clarity.
PAGE 20
SECTION 3: SOFTWARE SETUP —— USER GAMMA: 0.05 ~ 1.00 steps PED LEVEL: 0 ~ 63 steps COLOR GAIN: 0 ~ 255 steps NEG.IMAGE: You can invert a color image, or a black and white image. (OFF/ON) COMM ADJ.: —— —— —— —— —— CAM ID: Select the camera ID. 1 ~ 255 BAUD RATE: Select serial communication speed: 2400 / 4800 / 9600 / 19200 / 38400 / 57600 bps PROTOCOL: Select operating protocol. PELCO-D / PELCO-P DISPLAY ID: Select display item. OFF/ON ID POS: You can adjust ID position on screen.
PAGE 21
SECTION 4: SPECIFICATIONS SECTION 4 Specifications Table 1. Model Differences Indoor Outdoor TDN IR BLK-CCD203VS BLK-CCD223VS -- -- BLK-CCD205VH BLK-CCD225VH √ -- BLK-CPD206VH BLK-CPD226VH √ √ TDN: True Day & Night, uses an IR cut filter instead of switching the image to black and white. IR: Built-in infrared LED array Table 2.
PAGE 22
SECTION 4: SPECIFICATIONS Component Value HLC All Day / Night / (0~255 steps) Day&Night Auto / Color / BW / Ext Auto Level / Delay selectable BW Burst off/on / IR Smart off/on (Gain/level selectable) DPC Dead Pixels Compensation Special Title / MD / PM / Parking / Image / Comm / Language / Version Cam Title Text edit Motion Off / On (4 position) Privacy Off / On (8 position) Park.
PAGE 23
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting Problem Solution Nothing appears on the screen. - Check the power connections. - Check the video cable connections. - Ensure that the lens mode is set to DC (VIDEO). The video image is not clear. - Clean the lens with a soft, clean cloth. - Adjust the monitor screen for room lighting conditions. - Move the camera if necessary. The screen is dark. - Adjust the contrast feature of the monitor.
PAGE 24
APPENDIX B: CAMERA DIMENSIONS APPENDIX B Camera Dimensions 2.95" 4.96" 1.38" 1.61" Camera with vandalproof housing 2.95" 1.52" 1.75" 1.81" 2.09" Camera with plastic housing 3.29" 20 www.digiop.