Operating instructions

ManualsBrandsBlack Widow Security ManualsAutomotiveBW X-Z Series

STANDARD FEATURES

Some of the system’s standard features include:

• 4-button remote transmitter

• LED Status indicator

• Valet/Override switch

• Extended Range Receiver

• 125dB Multi-tone siren

• Dual stage impact detector

• Remote panic

• Remote Valet mode

• Remote chirp delete

• Remote sensor bypass

• Passive or active arming

• Flashing parking lights

• Auto Rearming

OPTIONAL FEATURES

This system has many optional features that

may require additional parts and/or labor.

Please contact your dealer for more details.

• Remote keyless entry (door lock/unlock)

• Illuminated entry

• LCD 2-way Remote

• Hood & trunk protection

• Trunk/hatch release

• Window roll-up

• Additional sensors

• Remote Start (optional plug-in module)

• Stop & Go Feature

• Auto Cold Start

Note: Some features may not be appropriate

for certain vehicles.

REMOTE TRANSMITTER BUTTONS

NOTE: Transmitter cosmetics may differ

between models and between standard 1-way

and LCD 2-way transmitters, but button

functions remain the same as described below.

Each transmitter button has two operating

modes: standard and level shifted. Pressing a

transmitter button for less than one second

activates the standard function associated with

that button (such as arm or disarm). Pressing a

button for more than one second changes the

color of the standard transmitter’s LED to

green and activates the level shift feature.

While the LED is green (level shifted), pressing

any transmitter button accesses another level

of commands providing expanded operation.

Transmitter Icons

Button 1 Button 2

Button 3 Button 4

SYSTEM MANUAL

VEHICLE SECURITY SYSTEM

Optional Remote Start Module and 2-way Transmitter Instructions Included

7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 1

Summary of content (24 pages)

PAGE 1
7250 rev 2 9-23.
PAGE 2
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 2 ARMING OPERATION To arm the system press transmitter button 1: • The siren will chirp once. • The parking lights will flash once. • The doors will lock.* • The LED will turn solid for 10 seconds then start flashing slowly. After 10 seconds the system is armed. During Arming, if the hood or trunk is open or the brake pedal is pressed, the system will wait 10 seconds for the zone to close.
PAGE 3
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 3 IGNITION CONTROLLED LOCKS The ignition controlled locks feature allows the doors to automatically lock when the brake pedal is pressed (after turning on the ignition and closing all doors), and automatically unlock when the ignition key is turned off. The ignition controlled locking feature may also be programmed for ignition lock without ignition unlock, and off (no ignition control).
PAGE 4
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 4 before activating the trunk release. NOTE: This feature must be programmed during installation and only functions if auxiliary is programmed for momentary output. VALET MODE When the system is placed into the Valet Mode the security and remote start features will be disabled. However, the optional keyless entry and trunk release features will still function if installed.The valet mode may be accessed with either the valet switch or a remote transmitter.
PAGE 5
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 5 To activate anti-carjack protection: 1. Make sure the ignition is on and all doors are closed. 2. Press the valet switch once. 4. Turn ignition off, then back on. 5. Press the override switch the number of times equal to the second digit of the PIN. 6. Turn ignition off. • The system will disarm. Example: PIN=2,3 Press valet switch two times, turn ignition off then back on, and press valet switch 3 more times.
PAGE 6
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 6 SURF MODE The Surf Mode allows the system to be armed or disarmed using just the key and override switch. While in surf mode the transmitter may be safely left at home or inside the vehicle’s trunk when engaging in an activity that may damage the transmitter such as surfing, swimming, white-water rafting, going over Niagara Falls in a barrel. To arm the system in surf mode: 1. Make sure ignition is on and all doors are closed. 2. Press valet switch 3 times.
PAGE 7
250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 7 MANUAL TRANSMISSION MODE On manual transmission vehicles, the remote start feature will not operate unless the proper vehicle exit sequence is performed. This operating mode protects against in-gear starting but is not completely without risk.
PAGE 8
7250 rev 2 9-23.
PAGE 9
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 9 OPTIONAL 2-WAY TRANSMITTER WITH LCD DISPLAY OPERATING INSTRUCTIONS REMOTE TRANSMITTER LAYOUT Button 3 Button 4 the 2-way transmitter also provides audible and vibration alert in case the display is out of view. And, for night-time use the LCD is equipped with a backlight feature which is activated by pressing button 5.
PAGE 10
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 10 OPTIONAL 2-WAY TRANSMITTER INDICATIONS The optional 2-way LCD transmitter displays more than 20 different screens to provide real-time indications for feature activation and system status. the different display indications are shown below for reference.
PAGE 11
7250 rev 2 9-23.
PAGE 12
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 12 VEHICLE SECURITY SYSTEM Optional Remote Start Module and 2-way Transmitter Instructions Included INSTALLATION INSTRUCTIONS BEFORE INSTALLING THIS PRODUCT PLEASE READ THE INSTALLATION DIRECTIONS THOROUGHLY!! BEFORE YOU BEGIN This system is compatible with electronic fuel injected engines only! Not intended for use with carbureted engines.
PAGE 13
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM ALARM MODULE WIRING 6-Pin Door Lock Harness Plug-in connector port for door lock harness. See Door Lock Wiring Diagrams • BLUE/BLACK WIRE - Lock relay N/C (87a) • BLUE WIRE - Lock relay Common (30). • GREEN WIRE - Unlock relay Common (30). • GREEN/BLACK WIRE - Unlock relay N/C (87a). • BLACK/RED WIRES - Lock/Unlock relays N/O (87). Connect this wire to the 14-pin harness short RED wire or short BLACK wire for polarity input.
PAGE 14
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 14 • GREEN/YELLOW WIRE - Parking Light output (+) 7.5A relay. Used for vehicle’s with independent left and right parking light circuits; see GREEN/BLACK wire. • YELLOW WIRE - +12V Ignition input. Connect to a main ignition wire at the ignition switch harness.This wire shows +12V when the ignition is on and while cranking. The voltage must not drop when the car is starting. • GRAY WIRE - Siren output (+) 2A. Connect to the siren’s red wire.
PAGE 15
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM • BLACK/YELLOW WIRE (small) - not used. • BLACK/YELLOW WIRE (large) - Start output (+). Connect to the vehicle’s starter wire. NOTE: If using the supplied starter defeat/antigrind relay socket, the large BLACK/YELLOW wire should be connected to the same point as the solid BLUE wire from the relay socket. • RED WIRE -Main power input (+).
PAGE 16
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 16 Complete Default Reset Follow this procedure to set the Programming Features to factory default settings. 1. Enter Alarm or Remote Start Feature program mode. 2. After entering programming mode, press Transmitter Button 1. • The siren will chirp once indicating the reset signal was received. • All Programming options are now set to factory default settings. 3. Turn ignition off. SYSTEM PROGRAMMING Entering Programming To enter System Programming 1.
PAGE 17
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM unlocks when ignition is turned off.The system will not lock if any door is open when the ignition is turned on. Brake/On mode- the doors will lock after closing all doors and pressing the brake pedal with ignition on; the doors will unlock when ignition is turned off. On/On mode- the doors will automatically lock or unlock when ignition is turned on and off. On/Off mode- the doors will automatically lock with ignition, but not unlock with ignition.
PAGE 18
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 18 Remote Start Programmable Features 1. Engine Run Time. Selects between 10, 15, 20, and 30 minute run cycles. 2. Turbo Timer Feature. For vehicles equipped with a turbocharger, this feature allows the engine to continue running for up to 6 minutes after the ignition is turned off, so the turbo has time to cool down. 3. Cold Temperature Starting. Allows the vehicle to automatically start and run every 1, 2, 4, or 12 hours for severe cold weather. 4.
PAGE 19
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM REMOTE START NOTES Smart Start and Tach Start In order for the system to properly start and run the vehicle, the unit must be able to determine if the engine is cranking or if the engine is actually running. This system is equipped with two means of detecting the engine’s run status: Smart Start and Tach Start.
PAGE 20
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Passive Transponder Systems: Passive transponder systems have become the most popular anti-theft system among vehicle manufacturers (Ford, Honda, BMW, Toyota, Nissan and others). This system requires use of a tiny passive transmitter housed in the base of the key. This device activates when placed close to the vehicle’s ignition switch.
PAGE 21
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 21 STARTER DEFEAT RELAY WIRING DIAGRAMS The Starter Defeat/Anti-Grind relay socket can be wired in either normally closed or normally open configuration. In either configuration, the Starter Defeat relay also provides Anti-Grind protection during remote start control, to prevent accidentally grinding the starter if attempting to start the vehicle using the key. The main unit default setting is normally closed operation.
PAGE 22
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 22 RELAY WIRING DIAGRAMS HORN HONK DIAGRAMS DOME LIGHT DIAGRAMS DEFROSTER DIAGRAMS TRUNK RELEASE DIAGRAM OPTIONAL HEADLIGHT ACTIVATION Program the Auxiliary output for timed operation and the headlights will turn on with Auxiliary for the preset timer duration then automatically turn off. Program the Auxiliary output for latched operation and the headlights will turn on with Auxiliary and remain on until the Auxiliary function is pressed again.
PAGE 23
7250 rev 2 9-23.qxd 9/24/2004 12:54 PM Page 23 DOOR LOCK WIRING DIAGRAMS NEGATIVE PULSE LOCK SYSTEM POSITIVE PULSE LOCK SYSTEM ADDING ACTUATORS VACUUM LOCK SYSTEM REVERSE POLARITY LOCK SYSTEM NOTE: The Black/Red door lock polarity input wire connects to the short Red or short Black wire in the 14pin main harness depending on door lock circuit type. For vacuum systems cut the Red/Black jumper to separate the lock/unlock relay inputs, and connect each side of the wire to the proper polarity.
PAGE 24
7250 rev 2 9-23.