Instruction Manual book SPECIFICATION Wingspan : Length : Weight : Radio : Servo : Engine : 2,080 mm 1,680 mm 6.2 kg 06 channels. 06 servos. 81.89 in. 66.14 in. 13.64 Lbs. 30-35 CC Gas(FUJI IMVAC). Made in Vietnam.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your EDGE 540-V3 30cc. Use the parts listing below to identify all parts. WARNING. Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU ASSUME ALL RISK & RESPONSIBILITY.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else. Please keep your safety and well-being in mind at all times.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . REPLACEMENT SMALL PARTS 1. 1. 4. 2. 2. 6. 5. 3. 7. 9. 8. 1. Aluminium landing gear. 2. Wheel pants. 3. Wheels. 4. Fuel Tank. 5. Plastic parts for rudder pushrod. 6. Rudder plastic light. 7. Plastic parts for landing gear. 8. Spinner. 1. Using the thread as a guide and using 9. Tail gear set. masking tape, tape the servo lead to the end of the thread: carefully pull the thread out.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . INSTALLING THE AILERON LINKAGES 1. Secure. Installing the aileron linkages as pictures below. 75 mm 3x12 mm. Repeat the procedure for the other wing half. INSTALLING THE AILERON CONTROL HORN 1. Attach the clevis to the outer hole in the control horn. Secure. 3 x 30 mm. Install aileron control horn as same as picture below. Secure. Elevator control horn1 C/A glue. Repeat the procedure for the other wing half.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Elevator control horn 2 C/A glue. 2.INSTALLING THE AILERON SERVO- 2. INSTALLING THE AILERON LINKAGES 2. Installing the aileron linkages as pictures below. Electric way 75 mm thread 3x12 mm. Secure. Secure. INSTALLING THE AILERON CONTROL HORN 2. Secure. 3 x 30 mm. C/A glue.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual C/A glue. FUEL TANK. Repeat the procedure for the other wing half. INSTALLING THE ENGINE MOUNT. See pictures below: INSTALLING THE ST OPPER ASSEMBLY 1) The stopper has been pre-assembled at the factory. 2) Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank and move freely inside the tank).
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . Secure. Tygon gas tubing not included. Vent tube Fuel pick- up tube Fuel fill tube 5) Test fit the stopper assembly into the tank. It may be necessary to remove some of the flashing around the tank opening using a modeling knife. If flashing is present, make sure none of it falls into the tank.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . INSTALLING THE ENGINE MOUNT. See pictures below: 5x 90mm Throttle - cable Secure. INSTALLING THE THROTTLE - CABLE. 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the arm.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Left side. Landing gear. Secure. Right side. MAIN GEAR INSTALATION. PARTS REQUIRED 2) Using the hardware provided, mount the main landing gear to the fuselage. 1) Assemble and mounting the wheel pants as shown in the following pictures. 6x 20mm Cut.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Remove the covering Secure. Drill 8mm hole. Secure.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . COWLING. 1. Slide the fiberglass cowl over the engine and line up the back edge of the cowl with the marks you made on the fuselage. Trim and cut Bottom side. Top side 2. While keeping the back edge of the cowl flush with the marks, align the front of the cowl with the crankshaft of the engine. The front of the cowl should be positioned so the crankshaft is in nearly the middle of the cowl opening.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . Epoxy glue. C/A glue. Bottom side. Mark line. Remove the covering 3) A drop of C/A glue on the wheel collar screws will help keep them from coming lose during operation. Bottom side.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Front view INSTALLING THE SPINNER. Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 8mm machine screws. INSTALLING THE ELEV ATOR SERVOS. 1. Install the rubber grommets and brass collets into the elevator servo. Test fit the servo into the servo tray. 2. Mount the servo to the tray using the mounting screws provided with your radio system. Secure Secure.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Secure HORIZONTAL STABILIZER. Horizontal stabilizer installation See picture below. 3 x 15 mm. Bottom side Aluminium 9mm. 3 x 15 mm. 221 mm. Secure. Secure.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . ELEVATOR CONTROL HORN INST ALLATION. Elevator control horn install as same as the way of aileron control horn. Please see pictures below. Secure. 3 x 25 mm. Bottom side. Elevator pushrod Elevator pushrod RUDDER SER VO INSTALLATION. Elevator control horn. ELEVATOR PUSHROD INST ALLATION. Elevator pushrod install as same as the way of aileron pushrod. 125 mm 3x12 mm. Ru ca dde ble r p us . hpu ll Ru dd er Secure. 16 Se rv o.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . Bottom side. RUDDER CONTROL HORN INST ALLATION. Rudder control horn install as same as the way of aileron control horn. Please see pictures below. Aluminium Control horn of Rudder. 3 x 40 mm A+B EPOXY PLUS glue A + B Epoxy Plus glue. Bottom side. Top side.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . RUDDER PUSHROD INSTALLATION. 1. Rudder pushrod install as same as the way of aileron control horn. 2. Rudder push - pull system install as same as picture below. 3 x 12mm C/A glue. Secure. Bottom side Elevator pushrod Rudder cable. Rudder cable. Elevator pushrod Rudder cable. Rudder cable. Plastic p arts of rudder pushrod. 3 x 12mm Cut. 18 Secure.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual Remove the covering Secure. Mark line. Remove covering. R ca udd bl er e. p us hpu ll Rudder plastic light.
EDGE 540 V3-30cc - Item code: BH94 . Instruction Manual C/A Epoxy. C/A glue. Secure. MOUNTING THE TAIL WHEEL BRACKET. 3x12mm 3x15mm Drill a hole 3mm diameter. Bottom side.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . INSTALLING THE SWITCH. Tie wrap. 1. Cut out the switch hole using a modeling knife. Use a 2mm drill bit and drill out the two mounting holes through the fuselage side. 2. Secure the switch in place using the two machine screws provided with the radio system. Tie wrap. Switch Switch BATTERY. INSTALLING THE RECEIVERAND BATTERY. 1. Plug the servo leads and the switch lead into the receiver.
EDGE 540 V3-30cc - Item code: BH94 Instruction Manual . WING ATTACHMENT. Locate the aluminium wing dihedral brace. aluminium 4 x 35mm 25mm 851mm. *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the edges and ends of the brace until it fits properly. Drill 3mm hole. Secure. RECEIVER. Left wing. See picture wing attach to fuselage. Installing the fuselage hatch as same as picture below. Wing bolt.
EDGE 540 V3-30cc - Item code: BH94 Drill 3mm hole. . Instruction Manual BALANCING. 1) It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 83MM BACK FROM THE LEADING EDGE OF THE WING. Secure. 2) Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing 83mm back from the leading edge, at the fuselage sides. 3.
EDGE 540 V3-30cc - Item code: BH94 . CONTROL THROWS. 1) We highly recommend setting up a plane using the control throws listed. 2) The control throws should be measured at the widest point of each control surface. 3) Check to be sure the control surfaces move in the correct directions. Ailerons : 25mm up 25mm down Elevator : 25mm up 25mm down Rudder : 40mm right 40mm left 25mm 25mm 25mm 25mm 40mm 40mm PRE-FLIGHT CHECK.
