MiniRaQ 4G Secure Series Installation Guide Manual #: 90-091 Revision: 1 MiniRaQ --- Part Number MRQ3X1S10, S12, S14, and S16 ________________________________________
MiniRaQ 4G Secure Series · Installation Guide Copyright © Black Hawk Labs, LLC. All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Black Hawk Labs.
Operators Safety Summary The general safety information is designed for installation and operating personnel. Safety and Handling Use all proper safety and handling practices when installing and operating this product. Grounding the Product A dedicated ground stud is provided at the left of the product, near the bottom. To ensure safety to all installation and operational personnel, connect a ground wire from this stud to earth ground using a minimum 14AWG.
What’s In the Box? 4 ‐‐‐‐‐‐‐‐‐ Assembled MiniRaQ Secure 4G Installation Guide (90-091) Hardware Kit (12-24 screws, Qty. 15) Hardware Kit (18-8 screws. Qty. 10) Keys (Qty. 2) 90‐091 Rev.
Table of Contents Chapter 1 Introduction………………………………………………..…………………………………6 How to Use This Guide……………………………………………………………………………...6 Navigating………………………………………………………………………………………………….6 About the MiniRaQ 4G Secure……………………………………………………………………………………...6 Overview…………………………………………………………………………………………………...6 Features…………………………………………………………………………………………………...7 Chapter 2 Hardware Orientation…………………………………………………………………..8 MiniRaQ 4G Secure Description………………………………………………………………………………….
1. Introduction How to Use This Guide How to Use This Guide This section provides important tips for locating this Installation Guide in its electronic “PDF” form. Navigating To navigate to the desired location, go to our website, www.bhlpower.com. Therein, the MiniRaQ 4G Secure Installation Guide may be found in two ways: ‐ ‐ Click on the hyperlink of the specific MiniRaQ 4G Secure product you are researching. Follow through to the Documentation tab. There you will find a hyperlink to the “90-091 Rev.
1. Introduction About the MiniRaQ 4G Secure Please note: To ensure trouble-free installation of your MiniRaQ 4G Secure, please review the following sections: o Chapter 2, “Hardware Orientation” on page 8. o Chapter 3, “Installation” on page 11. Should you have any questions regarding the installation of the MiniRaQ 4G Secure, please consult with the factory. Refer to Appendix B, “Contact Information” on page 17 for details.
2. Hardware Orientation MiniRaQ 4G Secure Description MiniRaQ 4G Secure Description The figure below illustrates the MiniRaQ 4G Secure’s external features: 1 2 1) Six removable Access Panels (2 top, 2 bottom, and 2 lower sides), for cable entry and communication management options. 2) Locking cover allows for maximum security, even in an unsecure environment. 8 ‐‐‐‐‐‐‐‐‐ 90‐091 Rev.
1. Hardware Orientation MiniRaQ 4G Secure Description The figure below illustrates the MiniRaQ 4G Secures’ internal features: 1) 2) 3) 4) 5) 9 4U of dedicated horizontal space for patch panel or other shallow rack-mounted equipment. Bonus 2U internal-to backplate vertical equipment space. 4U to 10U side panel vertical equipment space. Integrated level to facilitate installation. Integrated bridge lances for wire management. ‐‐‐‐‐‐‐‐‐ 90‐091 Rev.
2. Hardware Orientation MiniRaQ 4G Secure Description Product Overview This vertical rack system is available with 4U, 6U, 8U, and 10U side panels allowing a maximum U space utilization of 10U to 16U when using the internal 2U equipment flanges and 4U patch panel space. The internal 2U combines with the U spacing provided with the side panels to enable deployment of deeper rack-mounted equipment. The MiniRaQ 4G Secure is designed from heavy gauge steel and finished to last a lifetime.
3. Installation Safety Precautions Safety Precautions For all MiniRaQ 4G Secure installation procedures, observe the following safety and handling rule to avoid damage to yourself and the equipment: Important A dedicated ground stud is provided at the bottom left of the backplate. To ensure safety to all installation and operational personnel, connect a ground wire from this stud to earth ground using a minimum 14AWG in size.
Accessory Information Accessory 12 Description Quantity BH1001 Hardware Kit #12‐24 PH Screw Black 25 BH1002 Hardware Kit #12‐24 PH Screw Black 100 BH1003 1U x 3” Riser Bracket Set (w/ screws) 2 BH1004 1U x 6” Riser Bracket Set (w/ screws) 2 BH1010 2U x 3” Riser Bracket Set (w/ screws) 2 BH1011 2U x 6” Riser Bracket Set (w/ screws) 2 BH1005 1U Blanking Panel 19” x 1.
BH2019 16” x 16” x ¾” Plywood Insert 1 BH2020 Brush Cover Access Plate 2 BH2021 Backplate Pouch w/ Shelf 1 3. Installation Installation and Setup Be sure to follow hardware manufacturer’s recommended procedures for installing equipment in the MiniRaQ 4G Secure. Backplate Installation For Stud Mount Locate solid studs, 16” on center, before marking top two locations for pilot holes. Drill .156” holes for #10 coarse screws (supplied) into the backplate slots, spaced nominally at 16” at the top.
Side Panel Installation After ensuring the backplate has been properly and completely fastened to the wall, install the side panels by inserting the side panel hooks into the rectangular cutouts in the backplate. The smooth surface of the side panels are to face away from each other. All hooks must be engaged for proper assembly; apply downward pressure as required to seat panels fully.
Equipment Installation Your equipment can now be installed and configured. Screws used to mount your hardware should not be tightened until either the vented panel (supplied) or fan tray (optional accessory) has been installed and the front panel temporarily slid in place. This allows uniform spacing of the side panels and will insure proper seating of the locking cover. Also this allows for easy removal of the front panel and vent tray during any servicing of your equipment.
Cover Installation Place cover onto the side panels and slide toward the backplate. When properly seated, the cover should be flush against the backplate and level with the top of the backplate. The cover may then be locked with either of the two (2) keys provided. A.
B. Contact Information In This Appendix The following topics are discussed in this Appendix: Warranty Return Material Authorization (RMA) Contact Information Warranty All MiniRaQ 4G Secure products are designed and tested to the highest quality standards and are backed by a full 5-year parts and labor warranty. Warranties are effective upon delivery date to customer and are non-transferrable.
B. Contact Information Contact Information Contact Information Black Hawk Labs, LLC. 829-B West Stadium Lane Sacramento, CA 95834 Phone: (916) 923-0800 Fax: (916) 923-2851 Website: www.bhlpower.com C.
Limited Factory Warranty BlackHawk Labs, LLC Limited Factory Warranty: The limited warranty provided by BlackHawk Labs, LLC (BHL) in this Statement of Limited Factory Warranty applies only to Products purchased for commercial or industrial use in the ordinary course of your business. Terms of Warranty: BHL warrants its products to be free from defects in materials and workmanship for a period of five years (two years in Japan) from the date of purchase.
DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER BHL HAS BEEN ADVISED IN ADVANCE OF THE POSSIBLY OF SUCH DAMAGES. SPECIFICALLY, BHL IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUTES, CLAIMS BY THIRD PARTIES, OR OTHERWISE.
