Specifications

8
ENGLISH
(Original instructions)
Features
This tool includes some or all of the following features.
1. On/off switch
2. Side handle
3. Spindle lock
4. Guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (g. A)
The tool is supplied with a guard intended for grinding purpos-
es only. If the unit is intended to perform cutting off operations,
a guard specic for this operation must be tted. A suitable
guard for cutting off operations part numbers 1004484-06 for
KG701/KG901 and 1004484-07 for KG902 are available and
can be obtained from Black & Decker service centres.
Fitting
u Place the tool on a table, with the spindle (5) facing up.
u Release the clamping lock (7) and hold the guard (4) over
the tool as shown.
u Align the lugs (8) with the notches (9).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (7) to secure the guard to the
tool.
u If required, tighten the screw (6) to increase the clamping
force.
Removing
u Release the clamping lock (7).
u Rotate the guard clockwise to align the lugs (8) with the
notches (9).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (2) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(g. B - D)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (10) onto the spindle (5) as shown
(g. B). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (11) onto the spindle (5) as shown (g. B).
If the disc has a raised centre (12), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (13) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. C). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. C).
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. D).
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. D).
u Remove the outer ange (13) and the disc (11).
Fitting and removing sanding discs (g. D & E)
For sanding, a backing pad is required. The backing pad is
available from your Black & Decker dealer as an accessory.
Fitting
u Place the inner ange (10) onto the spindle (5) as shown
(g. E). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (15) onto the spindle.
u Place the sanding disc (16) onto the backing pad.
u Place the outer ange (13) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. D). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. D).
u Remove the outer ange (13), the sanding disc (16) and
the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
u Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
u Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.