KG701 KG901 KG902
A B C D 2
13 16 15 10 5 E 3
ENGLISH (Original instructions) Intended use Your Black & Decker angle grinder has been designed for grinding and cutting metal and masonry using the appropriate type of cutting or grinding disc. When fitted with the appropriate guard, this tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions.
(Original instructions) d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.
ENGLISH (Original instructions) Do not operate the power tool near flammable materials. Sparks could ignite these materials. u Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Note: The above warning does not apply for power tools specifically designed for use with a liquid system.
(Original instructions) u u Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel. Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
ENGLISH (Original instructions) Features This tool includes some or all of the following features. 1. On/off switch 2. Side handle 3. Spindle lock 4. Guard Assembly Warning! Before assembly, make sure that the tool is switched off and unplugged. u u u u Fitting and removing the guard (fig. A) The tool is supplied with a guard intended for grinding purposes only. If the unit is intended to perform cutting off operations, a guard specific for this operation must be fitted.
ENGLISH (Original instructions) Switching on and off To switch on, slide the on/off switch (1) forward then press it in. Note that the tool will continue running when you release the switch. u To switch off, press the rear part of the on/off switch. Warning! Do not switch the tool off while under load. u Hints for optimum use u u Firmly hold the tool with one hand around the side handle and the other hand around the main handle. When grinding, always maintain an angle of approx.
ENGLISH (Original instructions) LpA (sound pressure) 92.6 dB(A), Uncertainty (K) 3 dB(A) LWA (sound power) 103.6 dB(A), Uncertainty (K) 3 dB(A) Vibration total values (triax vector sum) according to EN 60745: Surface grinding (ah,SG) 9.9 m/s2, uncertainty (K) 1.5 m/s2 Cutting-off (ah) 6.2 m/s2, uncertainty (K) 1.5 m/s2 Polishing (ah,P) 4.6 m/s2, uncertainty (K) 1.5 m/s2 Disc sanding (ah,DS) 9.6 m/s2, uncertainty (K) 1.5 m/s2 Wire brushing (ah) 10.2 m/s2, uncertainty (K) 1.
14 E16307 15 56 55 4 32 21 20 1 2 3 32 22 25 24 27 29 www.2helpU.com 26 49 38 30 48 31 47 33 34 39 39 45 46 36 52 50 35 43 KG901 - KG902 - KG701 44 37 51 15 17 - 05 - 11 53 54 1 TYP.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel. 01753 511234 Fax 01753 551155 ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.