BDCS36G
A B C D E F 2
(Original instructions) Intended use Your Black & Decker screwdriver has been designed for screwdriving applications. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
ENGLISH (Original instructions) 3. Personal safety a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always wear eye protection.
(Original instructions) e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc.
ENGLISH u u u Hold power tool by insulated gripping surfaces when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
(Original instructions) Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated.
ENGLISH (Original instructions) Electrical safety # u Your charger is double insulated; therefore no earth wire is required. Always check that the mains voltage corresponds to the voltage on the rating plate. Never attempt to replace the charger unit with a regular mains plug. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Features This tool includes some or all of the following features. 1.
(Original instructions) The charger may hum and become warm while charging; this is normal and does not indicate a problem. Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40 °C. Recommended charging temperature: approx. 24 °C. Low battery indicator When the battery charge becomes low the LED work light will begin to flash. u The LED Flash will last 5 seconds during Low voltage --- --- --- at this pattern..
ENGLISH (Original instructions) Hints for optimum use Screwdriving u Always use the correct type and size of screwdriver bit. u If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant. u Always hold the tool and screwdriver bit in a straight line with the screw. Maintenance Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance.
(Original instructions) You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Batteries Z u Run the battery down completely, then remove it from the tool. NiCd, NiMH and Li-Ion batteries are recyclable.
ENGLISH (Original instructions) EC declaration of conformity % MACHINERY DIRECTIVE BDCS36G Black & Decker declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-2 These products also comply with Directive 2004/108/EC and 2011/65/EU. For more information, please contact Black & Decker at the following address or refer to the back of the manual.
(Original instructions) ENGLISH To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Please visit our website www.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90585906 REV-0 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
