Specifications

ManualsBrandsBlack & Decker ManualsFood ProcessorFX1200

MA Lighting Technology GmbH

Dachdeckerstr. 16

D-97297 Waldbüttelbrunn

www.malighting.de eMail: info@malighting.de

1.51.5

1.5

Safety Requirements (Important, read carefully!)Safety Requirements (Important, read carefully!)

Safety Requirements (Important, read carefully!)

1.5.11.5.1

1.5.1

TouchscreenTouchscreen

Touchscreen

Never use any sharp items when operating the touchscreens! Deep scratches will damage the screen. During

operation, due to temperature fluctuations, the calibration of the touchscreens may change, so an adjustment may

be necessary.





2.122.12

2.12 Settings in the Setup Menu (point 1)

1.5.21.5.2

1.5.2

Sockets for keyboard and mouseSockets for keyboard and mouse

Sockets for keyboard and mouse

These sockets are located on the rear of the unit and are very delicate; especially during transport, take care that

these parts are not exposed to mechanic stress.

1.5.31.5.3

1.5.3

Transportation/CaseTransportation/Case

Transportation/Case

During transport, take care that the touchscreens are not exposed to mechanical stress. Flightcases not provided by

MA Lighting have to be designed in a way that

under no circumstancesunder no circumstances

under no circumstances pressure can be exerted on the TFT

displays.

1.5.41.5.4

1.5.4

anel anel

anel (grandMA only)

If the mechanical parts of the display panel have not been moved for a period of time (24 hours typically), you may

feel a stronger resistance when adjusting the angle. This is normal and related to the mechanics of the pannel.

1.5.51.5.5

1.5.5

Battery Battery

Battery (not on the ultra-light)

In case of power failure, the console offers (with fully charged battery) an emergency backup of at least 12 minutes.

In case of a power failure, the console will automatically switch off after approximately another 3 minutes or

another 12 minutes when CONTINUE is pressed. If

this occurs this occurs

this occurs, the console will

automatically save all automatically save all

automatically save all

datadata

data.

When switching off the unit via

built-in power switchbuilt-in power switch

built-in power switch, all current show data is saved automatically.

In case of an automatic shut-down after a power failure (described above), the unit must be running for

at leastat least

at least

10 minutes, in order to guarantee a proper SAVE procedure the next time the unit is switched off.

By ignoringBy ignoring

By ignoring

this advice the harddisk may be be damaged.this advice the harddisk may be be damaged.

this advice the harddisk may be be damaged.

The battery needs approximately 4–8 hours for a full recharge. Only then the battery is able again to bridge another

power failure of up to 12 minutes.

According to manufacturer provisions, the battery has to be changed

after 5 years at latest after 5 years at latest

after 5 years at latest. Please attach a

label on the unit, indicating the date of purchase, preferably update data etc. (choose a location, where this

information can easily be seen). (This manual was printed in the year 2003.)

1.5.61.5.6

1.5.6

HarddiskHarddisk

Harddisk

During operation, do not push or knock the unit.

The built-in notebook harddisk is secured by a rubber-upholstery, however, mechanical stress can still damage the

unit and lead to e.g. a complete loss of data.

Please read the appropriate notes and warnings given under „Autosave“ and „Oops Settings“, if the unit is to be used

in very loud environment!

1.5.71.5.7

1.5.7

HousingHousing

Housing

– Do not block or cover the ventilation. If there is a high ambient temperature, the display pannel (grandMA only)

should be at least 5 cm open to ensure sufficient ventilation.

– Do not place any drinks on the unit.

– Do not use excessive force when adjusting the viewing angle of the display panel (grandMA only).