Technical data

8
ENGLISH
(Original instructions)
Removing the carpet glider (Fig. F)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
u Place the front of your shoe onto the carpet glider removal
tab (21) and press down rmly.
u Lift the steam mop up off the carpet glider (14).
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. G & H)
Warning! Inspect the seal (22) on the steam nozzle (4) and
hose (23) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. G)
u Press in the clips (24) on either side of the hose (23).
u Press the hose (23) onto the steam nozzle (4) and release
the clips (24).
Important! Ensure that the hose (23) is securely fastened
before using the hand held steeam cleaner. If steam escapes
from the joint then the hose is not correctly t, allow the unit to
cool then remove and re-t the hose.
Attaching the variable stem jet nozzle (Fig. H)
u Press in the clips (26) on either side of the variable stem
jeet nozzle (27).
u Press the variable stem jet nozzle onto the steam nozzle
(4) or the hose (23) and release the clips (26).
Important! Ensure that the variable stem jet nozzle (27) is
securely fastened before using the hand held steeam cleaner.
If steam escapes from the joint then the variable steam jet
nozzle is not correctly t, allow the unit to cool then remove
and re-t the variable steam jet nozzle.
Attaching other accessories (Fig. G)
u Align the lugs on the hose with the recesses on the acces-
sory.
u Press the accessory (25) onto the hose (23) and twist
anti-clockwise untill the accessory clicks into place.
Note! The variable stem jet nozzle may be used without the
hose by tting them directly to steam nozzle. All other acces-
sories must be connected to the hose for use.
Removing the hose and accessories(Fig. G & H)
Warning! The Steam nozzle, variable steam jet nozzle, hose
and accessories become hot during use. Allow the unit and all
accessories to cool before removing any accessories.
Removing an accessory (Fig. G)
u Twist the accessory (25) clockwise then pull away from
the hose (23).
Removinging the hose (Fig. G)
u Press in the clips (24) on either side of the hose (23) and
pull away from the steam nozzle (4).
Removinging the variable steam jet nozzle (Fig. H)
u Press in the clips (26) on either side of the vaiable steam
jet nozzle (27) and pull away from the steam nozzle (4).
Filling the water tank (Fig. I)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Open the ller cap (7) by ipping it down.
u Using the jug, ll the water tank (8) with water.
Warning! Your water tank has a 0.35 litre capacity.
u Re-t the ller cap (7).
Note: Ensure the ller cap is rmly secured.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro bre
pad tted and a continuous run time of 90 seconds.
Switching on and off (Steam mop)
u To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is rst turned on the water res-
ervoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
u To switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Autoselect
TM
Technology (Fig. J)
This steam mop is tted with an Autoselect
TM
button (6)
which shows various cleaning applications. They are used to