2821,2822,382083-01,00 5/8/02 12:42 PM Page 2 Black and Decker Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 Printed in USA (JAN03-CD-1) Copyright © 2002 Form # 382083-01 The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
821,2822,382083-01,00 5/8/02 12:42 PM Page 3 TM Instruction Manual 2821 2822 Adjustable Clutch Driver/Drill
2821,2822,382083-01,00 5/8/02 12:42 PM Page 4 Getting the most out of your tool. Please take time to read this manual and pay particular attention to the safety rules we’ve provided for your protection. If you have any questions about your tool please call: Cat # Voltage 2821 9.6V 1-800-9-BD TOOL 2822 12.0V Grip Style Chuck Capacity Battery Pack Mid. Standard Mid. Standard 3/8" Standard 0-350/0-1000 3/8" Standard 0-400/0-1200 RPM (1-800-923-8665) TORQUE ADJ.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 1 GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS • WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. • SAVE THESE INSTRUCTIONS • WORK AREA • • • • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 2 SERVICE • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 3 • • • • • • • • • • • Do not expose charger to rain or snow. These chargers are not intended for any uses other than charging B&D rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 4 • • Charge the battery packs only in B&D chargers. NOTE: Review and observe all of the “Important Charging Notes” in the charger instruction section of this manual. • NOTE: The batteries in your battery pack are the nickel–cadmium type. Cadmium is considered to be a toxic material by the Environmental Protection Agency.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 5 the charger has switched to its “equalize charge” mode which lasts approximately 4 hours, after which the charger will switch to “maintenance charge” mode. The battery pack can be removed at any time during these charge cycles, but will only be fully charged if the red light is continuously ON. The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep the battery pack fresh and fully charged.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 6 5. Under certain conditions, with the charger plugged in to the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 7 NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided. To turn the tool “ON,” squeeze the trigger switch. To turn the tool “OFF,” release the trigger switch (Figure 4). Your driver/drill is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 8 Dual Range Gearing Troubleshooting Tip! The dual range feature of your driver/drill allows you to shift gears for greater versatility. If you are having trouble changing gears, make sure that the dual range gear shifter is either completely pushed forward or completely pushed back. To select the low speed, high torque setting, turn the tool off and permit the unit to stop.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 9 chuck and personal injury may result. Always lock off trigger switch when changing accessories. Drilling 1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits. 2. Be sure the material to be drilled is anchored or clamped firmly.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 10 and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Drilling in Metals Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil; bacon grease will also serve the purpose.
2821,2822,382083-01,00 5/8/02 12:42 PM Page 11 Every B&D tool is of the highest quality.
