User Manual

8
ENGLISH
(Original instructions)
Note: To remove the cup charger from the charging
base pull out on the retaining tabs and lift the cup
charger out.
u Plug the charger into an appropriate outlet before
inserting the battery pack.
u Slide the battery pack onto the charging station.
3. Wall mounted vacuum storage and battery
charging
The product can be attached to a wall to provide a
convenient storage and charging point for the appliance.
When mounting to a wall, make sure the mounting method
is suitable for the wall type and is appropriate to the weight
of the appliance.
u Mark the location of the charging station screw holes on
the wall (within reach of an electrical outlet for charging
the vacuum while it is on the charging station.
u Fix the charging station to the wall using appropriate
screws and plugs for the type of wall, and weight of the
appliance.
u Install the cup charger into the charging station. Ensure
it is locked into place before proceeding.
Note: To remove the cup charger from the charging base pull
out on the retaining tabs and lift the cup charger out.
u Plug the charger into an appropriate outlet.
u With the battery installed on the vacuum, slide the charge
port (15), located on the vacuum base, onto the
rails of the charging station (5a).
u ThewhiteLED(3)onthevacuumwillashindicatingthat
the battery is being charged.
u The LED sections increase as the battery is charged -
when fully charged the LEDS go out. The pack is fully
charged and may be used at this time or left on the
charger.
Leaving the battery in the charger
The charger and battery pack can be left connected with
thegreenLEDglowingindenitely.Thechargerwillkeep
the battery pack fresh and fully charged.
To install battery pack (g. B)
u Insert battery (4) into tool until an audible click is heard as
showningureB.
u Ensure battery pack is fully seated and fully latched into
position.
To remove battery pack
u Depress the battery release button and pull battery pack
(4) out of the tool.
Assembly (Fig. C)
u Align the top of the extension tube (9) with the vacuum
 inlet(16)asshowningureC.
u Push the extension tube (9) onto the vacuum inlet (16) so
it locks into position.
u Alignthebottomoftheextensiontube(9)withtheoor
 head(8)asshowningureC.
u Pushthebottomoftheextensiontube(9)ontotheoor
head (8) so it locks into position.
u To remove an accessory, press the accessory release
latch located on the accessory and pull it off.
USE
This vacuum cleaner can be used in one of four ways.
u Withtheextensiontube(9)andtheoorbrush(8)as
showningureC.
u Withtheoorbrush(8)andthevacuuminlet(16)as
showningureD.
u With the extension tube (9) and an accesssory tool (10),
(11),(13)or(14)asshowningureE.
u With an accesssory tool (10), (11), (13) or (14) and the
 vacuuminlet(16)asshowningureE.
u Accessories not supplied with your unit can be ordered
through service department.
Switching ON and OFF (Fig. F)
u ToswitchON,presstheOn/Offbutton(1).
u For increased power, slide the variable power switch (2)
forward.
Note:Theoorbrush(8)willpoweronwhenitis
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklightsonthefrontoftheoorheadwillilluminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note: The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON or during the charging
process.
u ToswitchOFF,presstheOn/Offbutton(1).
u Return the product to the charger immediately after use
so that it will be ready and fully charged for the next use.
Ensure that the product is fully engaged with the charger
plug.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
u 2 in 1 Accesssory tool (10)
u Crevice tool (11).
u Pet hair tool (13).
u Wide mouth dust brush (14).
u Theaccessorytool(10),(11),(13)or(14)canbetted
either directly to the extension tube ( 6 ) or to the vacuum
inlet (5) as shown in Fig. J.
u Align the top of the accessory tool (10), (11), (13) or (14)
with the vacuum inlet (16) or extension tube connection
(9a) and push into place so it locks into position as shown
ingureG.