PORTABLE DEHUMIDIFIER INSTRUCTION MANUAL CATALOG NUMBER BDT20WTB BDT30WTB BDT40WTB BDT50WTB BDT50PWTB Thank you for choosing BLACK+DECKER! PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON. If you have a question or experience a problem with your BLACK+DECKER purchase, go to www.blackanddecker.com/instantanswers If you can’t find the answer or do not have access to the Internet, call 844-299-0879 from 10:30 a.m. to 6:30 p.m. EST Mon. - Fri. to speak with an agent.
CONTENTS SAFETY INFORMATION Important Safety Instructions...........................................................................................................................................3-4 Grounding Instructions..........................................................................................................................................................4 Safety Guidelines.....................................................................................................................
SAFETY INFORMATION DANGER DANGER - Immediate hazards which WILL result in severe personal injury or death WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death CAUTION CAUTION - Hazards or unsafe practices which COULD result in minor personal injury IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical appliances, basic safety precautions should be followed, including the following 1.
SAFETY INFORMATION GROUNDING INSTRUCTIONS ELECTRICAL REQUIREMENTS The electrical requirements are a 115 volt 60 Hz, dehumidifier only, 15 amp. It is recommended that a separate circuit serving only the product be provided. The product is equipped with a 3-wire cord having a 3-prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded. This appliance must be grounded.
SET UP & USE PARTS & FEATURES Control Panel & Digital Display Air Outlet Water Collection Bucket Water Level Indicator Handle Filter Castors (4) Drain Plug Continuous Drain Kit Drain Adapter & Gasket Drain Hose Additional Pump Drain Kit (Model BDT50PWTB Only) Pump Drain Hose (16.
SET UP & USE CONTROL PANEL Pump LED Indicator (Model Timer ON BDT50PWTB) LED Indicator Bucket Full Digital LED Indicator Humidistat Continuous Display Drain LED High Fan Speed Timer OFF Indicator LED Indicator LED Indicator Clean Filter LED Indicator Filter Button Increase Room Humidity Level Fan Speed Button Decrease Room Humidity Level Pump Button (Model BDT50PWTB) Power Button Timer Button ERROR CODES: (Will appear in the digital humidistat display) E1: The temperature sensor on the discharge pi
SET UP & USE INSTALLATION GUIDE When you open the box, you should have received: Portable dehumidifier User Guide Castors (4) Continuous Drain Kit If you purchased a model with a pump (BDT50PWTB) there will be an additional pump drain kit To Install Castors: 1. F or the 20 pint model (BDT20WTB) and the 30 pint model (BDT30WTB) gently lift the lid of the bucket (see fig 1). For the 40 pint model (BDT40WTB) and the 50 pint models (BDT50WTB, BDT50PWTB) gently lift off the lid of the bucket (see fig 2).
SET UP & USE BEFORE FIRST OPERATION 1. G rip each side of the bucket and pull to remove the bucket from the dehumidifier (Fig. 4). Fig. 4 2. C heck inside the bucket to make sure the float system is in the correct position. If not, place the float in the correct position (Fig. 5). Fig. 5 3. R e-insert the bucket once you have determined the float system is in the correct position (Fig. 6) Fig. 6 The float in the bucket is essential to the “bucket full” system working properly.
SET UP & USE OPERATION INSTRUCTIONS NOTE: Unit may shut off automatically during 24 hour period if collection bucket is full (see below). If continuous drainage mode is utilized, and drain hose is connected, the unit will operate continuously (see page 12). 1. P ress the POWER button once to turn the unit on. Press POWER button again when you’re ready to turn it off. 2. P ress the or buttons under the display to select the desired relative humidity in the room.
SET UP & USE NOTE: When the bucket is full or removed from the unit, the compressor will turn off but the fan will continue to run for a few minutes. This is completely normal. The dehumidifier will not be removing moisture from the air at this time. Over time, the dehumidifier will create a more stable humidity in the area it is located. The more moisture the dehumidifier removes from the air, the more often you may have to empty the bucket unless you choose to use the continuous drain option.
SET UP & USE FILTER CLEANING When the filter needs to be cleaned, the filter indicator light will come on (after approximately 250 hours of use). Remove the filter from the back of the unit by using your thumbs to press down on the filter tabs directly above the filter. Clean the filter with warm, soapy water and dry thoroughly before putting back in place. Once filter is back in the unit, press the FILTER button to reset the filter indicator. CAUTION: Do not clean the filter in a dishwasher.
SET UP & USE CONTINUOUS DRAINAGE Water can be automatically emptied by attaching the clear hose (included) or a standard garden hose (not included) to the drain port on the back of the dehumidifier. This will allow the unit to run continuously (depending on the selected humidity level) without having to empty the unit’s water collection bucket. To use with clear hose (included) 1. Place dehumidifier on a perfectly level surface. 2. U nscrew and remove drain cap to access the garden hose nozzle threads.
SET UP & USE To use with standard garden hose (not included) 1. Place dehumidifier on a level surface. 2. Unscrew and remove drain cap to access the garden hose nozzle threads. 3. Screw on garden hose to the now accessible nozzle threads. 4. O nce securely installed, lead the drain hose to a nearby drain lower than the height of the drain plug. (Make sure there are no kinks or knots in the hose) 5. Turn on the unit and select desired relative humidity level.
SET UP & USE INTERNAL PUMP MODE The internal pump allows the unit to operate without having to empty the bucket and requires the installation of the included pump drain hose kit. To install the kit, remove the drain cap on the back of the unit (see Fig. 6 on page 12). Insert the included gasket into the front of the included pump adapter (see Fig. 7 on page 12).
SET UP & USE GENERAL INFORMATION Recommended humidity levels: 30%-50% (Too dry, less than 15%, too humid, greater than 50%) During operation, it is normal for the exhaust coming from the side of the dehumidifier to be warm. Caused by preliminary factory testing, there may also be a small amount of water present in the bucket before using the dehumidifier for the first time, which is normal.
CARE & CLEANING CARE AND CLEANING GUIDE NOTE: Make sure power is off and power cord is not plugged into electrical outlet prior to performing and cleaning to the unit The water collection bucket should be cleaned every few weeks to prevent the growth of mold, mildew and bacteria. Use a mild detergent to clean the bucket. Once clean, completely dry the bucket and place it back inside the humidifier.
TROUBLESHOOTING & WARRANTY BEFORE YOU CALL FOR SERVICE IF THE APPLIANCE FAILS TO OPERATE: A) Check to make sure that the heater/fan is plugged in securely. If it is not, remove the plug from the outlet, wait 10 seconds and plug it in again securely. B) Check for a blown circuit fuse or a tripped main circuit breaker. If these seem to be operating properly, test the outlet with another appliance. IF NONE OF THE ABOVE SOLVES THE PROBLEM, CONTACT A QUALIFIED TECHNICIAN.
TROUBLESHOOTING & WARRANTY Troubleshoot your problem by using the chart below. If the dehumidifier still does not work properly, contact W Appliance Co. customer service center or the nearest authorized service center. Customers must never troubleshoot internal components.
TROUBLESHOOTING & WARRANTY Troubleshoot your problem by using the chart below. If the dehumidifier still does not work properly, contact W Appliance Co. customer service center or the nearest authorized service center. Customers must never troubleshoot internal components. TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Error Code “E1” The temperature sensor on the discharge pipe may be faulty and may need to be changed. Contact the customer service center.
TROUBLESHOOTING & WARRANTY LIMITED WARRANTY Any repair, replacement, or warranty service, and all questions about this product should be directed to BLACK+DECKER at 844-299-0879 from the USA or Puerto Rico. BLACK+DECKER warrants to the original purchaser that the product will be free from defects in material, parts and workmanship for the period designated for this product.
Page 21
BLACK & DECKER, BLACK+DECKER, the BLACK & DECKER and BLACK+DECKER logos and product names and the orange and black color scheme are trademarks of The Black & Decker Corporation, used under license. All rights reserved. Product in this box may differ slightly from that pictured. Does not affect function. Not all accessories shown in photography are included in this package. Imported by W Appliance, Inc.
