Use and Care Manual

OPERATING INSTRUCTIONS
TRIGGER SWITCH
This drill is equipped with a variable speed switch. The
drill speed depends on how far the trigger is pressed.
1. To start drill, gently squeeze the trigger switch (1)
(Fig. A).
2. To stop the drill, release the trigger switch.
NOTE: Drillingforanextendedperiodoftimemay
cause the drill motor to overheat. If drill gets hot, stop
drilling and allow it to cool for at least 15 minutes.
FORWARD/REVERSE BUTTON
The forward/reverse button (2) is mounted above the
trigger switch (1) (Fig. A).Tomakethedrillrotateclockwisefordrilling,pushtheforward/
reversebuttontotheright.Tomakethedrillrotatecounter-clockwise,pushtheforward/
reverse button to the left.
NOTES:
a)Neverchangethepositionoftheforward/reversebuttonwhilethechuckisturning.
b) There is no dead center position for the forward/reverse button. The tool will run only
when it is in either the full left or full right position.
INSTALLING DRILL BITS
WARNING:Neverholdthechuckbodywithonehandandusethedrillpowerto
rotate the drill body to loosen or tighten bits. Serious injury may result.
WARNING: To reduce the risk of injury, always
unplug drill from power supply before making any
adjustments or changing accessories.
Thisdrillisequippedwithakeylesschuck.
Thischuckisdesignedtoprovideeasytwo-handed
tighteningandlooseningofthechuckjaws.
1.Toopenthekeylessdrillchuck,graspandholdthe
chuckcollar(6)withonehand(Fig. B). Rotate the
chuckbody(3)inacounter-clockwisedirectionuntil
thechuckjaws(7)openwideenoughtoacceptthebit(8).
2.Insertthebitintothechuckthefulllengthofthejawsoruntilthespiralportionofthebit
isnearthechuckjaws.Raisethefrontofyourdrillslightlytopreventthebitfromfalling
outofthechuckjaws.
3.Tightenthechuckjawsontothebitbyturningthechuckbodyinaclockwisedirection.
NOTE: MakesurethebitisproperlyalignedinthejawsandNOTatanangle.An
improperlyalignedbitcouldbethrownfromthechuckwhenthedrillisstarted.
4.Finishtighteningthechuckjawsbyholdingthechuckcollarwithonehandandfirmly
tighteningthechuckbodybyrotatingitinaclockwisedirection.
NOTE: Handtightenthechuckjaws.DoNOTusepliers.
WARNING:Donotinsertthedrillbitintothechuck
and tighten as shown in Fig. C. The drill bit MUST be
properlyinsertedwithallthreeofthechuckjawsholding
thebitcenteredinthechuck.Failuretoproperlyinsertthe
drillbitcouldcausethedrillbittobethrownfromthechuck,
resultinginpossibleseriousinjuryordamagetothechuck.
REMOVING DRILL BITS
1.Toopenthekeylessdrillchuck,graspandholdthechuckcollarwithonehand.Rotate
thechuckbodyinacounter-clockwisedirectionuntilthechuckjawsopenwideenough
to release the bit.
2. Remove the bit.
TRIGGER SWITCH LOCK
WARNING: ThedrillshouldonlybelockedONwhenitisheldstationaryinadrillpress
standorothermeans;NOTBYHAND!Neverunplugthetoolwiththelockingfeature
engaged.Todosowillcausethetooltostartimmediatelythenexttimeitispluggedin.
Thetriggerswitchlock-onfeatureallowsthetriggerswitchtobelockedintheONposition
5
1
2
A
7
3
6
8
B
C