3 1 4 www.blackanddecker.co.
English 2 (Original instructions) 5
9 9 9 9 8 8 4 4 5 6 7 A 7 B 13 11 5 10 11 13 5 10 11 13 12 10 5 C D 3
13 16 14 15 13 10 11 5 E 4 F
Intended use Your Black & Decker angle grinder has been designed for grinding and cutting metal and masonry using the appropriate type of cutting or grinding disc. When fitted with the appropriate guard, this tool is intended for consumer use only. Safety instructions General power tool safety warnings Warning! Read all safety warnings and all ! instructions. Failure to follow all instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a.
Note: The above warning does not apply for power tools specifically designed for use with a liquid system. Kickback and related warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding.
Safety warnings specific for sanding operations Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. Safety warnings specific for polishing operations Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings.
Removing Use a screwdriver to remove the screws (9). Remove the flange (8), guard (4) and spring washer (7). Store these parts carefully. Warning! Never use the tool without the guard. Keep the spindle lock (3) depressed and tighten the outer flange using the two-pin spanner (14) (fig. E). Make sure that the outer flange is fitted correctly and that the disc is clamped tightly. Fitting the side handle Screw the side handle (2) into one of the mounting holes in the tool.
Maintenance Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance on corded/ cordless power tools: Switch off and unplug the appliance/tool. Or switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack.
EC declaration of conformity MACHINERY DIRECTIVE AST6, CD105, CD110, CD115 To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at: www.2helpU.
CD115 - CD110 - CD105 - AST6 - AST6XC TYP. 4 12 8 7 5 10 11 1 44 14 13 15 16 17 2 20 6 3 19 24 18 22 41 23 25 47 21 40 26 39 4 28 27 31 38 30 37 33 36 32 35 45 34 46 860 29 E16025 www.2helpU.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
$XVWUDOLD %ODFN 'HFNHU $XVWUDOLD 3W\ /WG )OHWFKHU 5RDG 0RRURROEDUN 9LFWRULD 1HZ =HDODQG %ODFN 'HFNHU 7H $SXQJD 3ODFH 0W :HOOLQJWRQ $XFNODQG 8QLWHG .
